Egg 6 sugar 135g.

83 grams of low flour and 57 grams of corn starch.

Cocoa powder 48 grams and butter 45 grams.

Milk105g

condiments

80 grams of chocolate and 60 grams of whipped cream.

500 grams of frosting and proper amount of pigment.

Land Rover's Steps in Fancy Car Cake

1.？ Mix and sieve low-flour corn flour.

Melt butter into liquid state in water, add milk and stir well with hand pump, and add cocoa powder and stir well.

Eggs and fine sugar are separated from warm water.

2.？ Regarding the sending status of sponge cake egg liquid, it didn't disappear for a few seconds as everyone said, but this time is always not well grasped. Later, I looked for it several times, and the whole egg liquid was like wet foam. The egg liquid on the egg head of the eggbeater does not flow down quickly, but drops slowly, even pulling up the wet foam tip, and then falls. This state depends on the thickness of the eggbeater you use. In a word, if you hear bubbling when you are dusting, it must be that the egg liquid is not delivered in place. Continue to add some time next time, and you will be able to master the skills of sending whole eggs after several attempts.

3.？ After beating the egg paste, sift in the flour for 4 times, cut and mix well, then add the cocoa butter milk paste and mix well. Enter the mold. Preheat in an oven at 160℃ and bake at 150℃ for 40-50 minutes.

4.？ I'm looking for photos of Land Rover on the Internet. I'd better look for the front, front and back. If it's best to play black and white, I can only play black and white, so I use my mobile phone to find pictures on the Internet to compare the colors of lights and the details of faces.

In addition to the above three kinds of drawings, it is best to print more big details, such as roofs, such as trolleys, etc.

Every time I find the front picture, I insert the picture in WORD, then cut it out, remove the redundant edges around the car, never change the proportion of the car, and then modify the picture size to 18CM long, so that I can cut it with an 8-inch mold. The front and back images are also cut, and the size of the image is defined according to the height of the front image after changing its length, so that it can be printed and cut, and a car has three sides.

5.？ Flowchart 1

1, 10 inch cocoa sponge, everything 2, front print.

2. Cut out the shape of the car through plastic wrap.

3. Try to keep the knife vertical when cutting, and leave more edges for decoration.

4. Cut the other half, too. Turn the picture upside down when you cut it. You can't face your heart without fighting. The crust is a little bulging and not very sticky.

5. Put the two pieces together, and the general shape of the car has appeared.

6. Cut the part of the window into an angle in proportion. At the same time, the angle of the front side of the car should also be cut off. I forgot when I made it, and I remembered it only after I put on chocolate sauce. Cut it now.

7. 80 grams of chocolate and 60 grams of whipped cream to melt the sauce. Put it in the middle first.

8. Stand up and insist.

9. Coat the whole car with chocolate sauce and smooth it as much as possible to avoid potholes when covering the sugar skin.

6.？ Flowchart 2

1, the coated cake should be refrigerated in the refrigerator to solidify the chocolate. Put it on something about the same size as the bottom. Here is a three-pound box, which is very suitable. Try to make a cake directly with it next time.

2. Stick a piece of soft candy on the top of the wheel to make it protrude above the wheel.

3. Roll the sugar skin flat, stir it up with two rolling pins and gently cover it. Smooth with a trowel

4. Cut off the excess jelly skin. The higher the temperature of the sugar skin, the softer it is, the better the operation and the faster the hand.

5, black and white, cut the wheel with two round dies, one big and one small. This circular cut is at 32PC. If not, you can cut it with a big flower mouth and a small flower mouth, or you can cut it with other round things. There is no need to buy tools to operate this regular shape.

6. Cut the white in the groove to make the wheel hub of the tire. I cut this with the yellow tool in the picture, because the wafer is very small and the sharp tool is not easy to operate. This straight-headed knife is made by ourselves and ground with a plastic stirring rod.

7. Paste the window black.

8. There is also a piece of fondant on it, because there is a small eaves behind the roof, so the back is longer. Open the skylight.

9. Continue to make details such as the security box. This sign is written with a brush dipped in silver.

The rest of the process is nothing, just some small details, such as car lights, reflective lights, door signs and so on. .

The process of making only the soft candy part took about 6 hours (including the time to pinch the pigment). . Making fudge cakes is a time-consuming job. .