Method:
1, winding with 3 bushings ***4.
3. mesh
4. Shape two slender circles and twist them clockwise twice at the tail.
5. Draw two circles into the shape of the butterfly's front wings.
6. The two front wings are tied together.
7. Tie the last two pieces together.
8. Wrap with paper tape
9. Adjust the shape of the front fender slightly.
1 1. Wind the electric wire on the adhesive tape, and then tighten the electric wire.
12, cut off the extra wires.
13, slightly bend the line into two whiskers.
14, after the butterfly is finished, you can put a pin on the adhesive tape and a butterfly pendant is finished.
And:
I. Materials and tools
(l) Colored metal wire, with many colors and models.
(2) Elastic screen, with various monochrome and bicolor.
(3) The flower cores have various shapes and colors. (4) Self-adhesive tapes have various colors.
(5) synthetic fiber thread for sewing.
(6) cotton. (7) White glue for carpentry.
(8) Quick-drying adhesive.
(9) scissors
(10) Pointed pliers.
(1 1) wound casing with a diameter of 8CM from ICM. It can also be replaced with cylindrical articles such as bottles and refills.
Second, the basic steps
Winding, weaving, assembling and modeling are all silk screens.
The four basic steps of flowers.
(1) hover
In the production of petals, receptacles and leaves, colored metal wires need to be wound into a circle first, just like their skeleton frame. For larger petals, leaves and receptacle, it is necessary to make them piece by piece, and the winding method is single winding method, while for smaller petals, leaves and receptacle, multi-winding method can be used, so that a multi-petal skeleton can be completed at one time. Some special flowers and leaves need to be circled more, and petals and leaves with veins need to be circled and then veined.
(1) single winding method
① Wrap colored metal wires on the casing 1 turn, and the ends of the metal wires are crossed.
(2) At a position about 5mm away from the surface of the sleeve, clamp the staggered place with fingers or pointed pliers and tighten it, and then rotate the sleeve longitudinally for 3-4 times.
③ Cut the wire at the end of winding, or leave a 2-5cm wire at the root of the coil.
(2) Multi-winding method
① The wire is bent at 5cm.
(2) Hold the bent part by hand and wind the long end of the metal wire on the sleeve.
(3) Continue to wind, * * * 3-6 times.
(4) Merge the four iron wires outside the circle.
⑤ Clamp and tighten the four wires, and then rotate the sleeve longitudinally for 3-4 times.
⑥ Cut off the loosened wires, or leave two wires 5 cm long.
(3) Multi-stage winding method
① First, complete the single loop winding method and change the loop into the required shape.
(2) Continue winding the rest of the wire, just like the figure of eight. The diameters of the upper and lower coils can be different as required.
(3) In the same way, three sections can be completed, and the size of each circle changes as needed.
(4) Wave circle method
① First, non-ferrous metal wires are wound around the knitting needles.
② Take it off the needle and stretch it.
(3) Then circle, which is the same as the single circle winding method.
(5) Preliminary finalization
The wound skeleton is round. According to the basic shapes of petals, leaves and flowers in the work, the required shapes are pinched by hand. Multi-winding method is formed as follows.
(1) Multi-turn pinch together.
(2) The coil is open.
③ Adjust to a proper position.
(2) Grid
(1) unicyclic grid
(1) Put a metal mesh evenly on the metal ring.
② Pull to the root of the circle.
(3) After winding the iron wire several times and binding it, directly pull the iron wire off. (4) Free modeling after completion.
(2) Multi-section grid
(1) with a single ring network.
② Screening and ligation.
(3) Cut off the redundant screen.
(4) Hold two circles with both hands, and twist a circle at the intersection of two sections, and then you can freely shape.
(3) Multi-loop grid
(1) Put it on the screen and pull it to the root of the circle, not too tightly.
(2) Tighten diagonally with a thread.
③ Wrap the petals one by one.
(4) root binding.
⑤ Cut off the excess screen at the root.
(3) Assembly
① Fix the flower core on the pedicel first.
② The lower part of petals is narrow.
(3) Tie a petal on the pedicel connected with the flower core, and don't break the line.
(4) Continue to tie one petal, repeatedly tie all petals, and then pull the wire.
⑤ Fix the receptacle on the pedicel.
⑥ Turn the socket up.
⑦ Tie a leaf at the proper position of the pedicel.
8 Tie the second leaf to the proper position of the pedicel.
Pet-name ruby with green or brown adhesive tape wrapped pedicels. Attending to complete assembly.
(4) Petals, receptacle and leaves can be stretched and bent at will, and petals, leaves, flowers and stems can be arranged and shaped according to the types of flowers and the blooming situation of flowers. The assembled flowers can obtain different effects as shown in the left picture by stretching and bending the petals.