Note: origami roses need to be prepared for many creases, and the paper needs to be folded repeatedly. The following is a detailed diagram.
Take a square piece of paper.
Fold in half horizontally, fold each side again, and fold again 1 time, leaving 7 horizontal creases on the paper.
Fold in half vertically, fold again on each side, and fold again 1 time, leaving 7 longitudinal creases on the paper.
Unfold the paper and fold it diagonally
After opening, leave a crease as above.
Fold up the corners.
Fold in half along the diagonal
Find the nearest line above the diagonal, which is connected by the intersection of horizontal and vertical creases, and then fold it.
The other diagonal line is also the same as the previous step, with a crease.
Open the picture above, and then fold it diagonally (red line in the picture).
The most basic steps
Fold according to this red line (diagonal of the small box at the bottom).
The most basic steps
Then unfold the paper.
The most basic steps
Turn the paper over.
Pinch up four diagonal lines, and the above picture shows the effect from above.
Fold the origami inward, and at the same time, press down the top square along its diagonal.
Fold the paper like this, the top and bottom paper must be folded in the opposite direction.
Put the origami flat, and that's it.
Flatten the origami, and fold the origami at the top left down according to the red line.
Ok, then spread the second half from the back, it looks like the top.
Then turn the bottom of the origami out and you can see the picture above. Note that it looks like a windmill after folding.
Fold down as shown by the red line.
Press the red line and fold the paper down.
Take a profile photo, I hope everyone can understand it better.
What it looks like when all four sides are completed. Patiently learn this step! This is not easy.
Folding mode of origami
Fold up two small triangles as shown by the red line.
Fold the triangle to the right as shown by the red line.
Then fold it to the left as shown by the red line.
All four sides are folded.
This is one of the recent photos of four folded legs.
Fold the origami in half and then turn it back as shown by the red line.
After all four are folded.
Four folded side views.
Seen from the top of the flower
This is the bottom of the flower.
Then fold one foot inward.
The second paragraph
The third leg
The fourth stop
Gently pull four petals outward to expose the flower core.
Gently press the edge of the petal to make the outer end of the petal produce a certain arc, just like a real petal.
In order to make the flowers look more beautiful, you can try different papers, because too thick or too thin paper will affect the folded flowers.
The last step of flowering is to decorate the petals properly to make them look more natural and beautiful. Of course, if you add branches and leaves, it will be more beautiful in a vase! Here's how to add branches and leaves to flowers!
These are the materials to be prepared. You can buy wire for flowers directly at the stationery store. If you have wire at home, you can also buy green tape (which is also necessary for making flowers) at the stationery store and wrap the wire. The effect is the same!
Put a circle on the wire to help fix the wire in the flower;
The making of leaves is very simple. Just cut a piece of green paper in the shape of a leaf and fold out the veins.
Insert the wire into the bottom of the flower and stick some double-sided tape on the bottom of the flower.
Wrap green sticky paper around the wire and stick the flowers and branches together. Although the green tape is sticky, if you feel that it is not sticky enough, you can also use double-sided tape to help. So I put some double-sided tape on the bottom of the flower last step.
After the flowers are fixed, you can add leaves.
What it looks like when flowers, branches and leaves stick together.
.................., this is a ... There's another one. ..........................
Fold the origami inward and press the center square down at the same time.
Fold the paper like this, the top and bottom paper must be folded in the opposite direction.
Then turn the bottom of the origami out and you can see the picture above. Note that it looks like a windmill after folding.
Press the red line and fold the paper down.
Take a profile photo, I hope everyone can understand it better.
Fold the origami in half and then turn it back as shown by the red line.
After all four are folded.
Gently pull four petals outward to expose the flower core.
Gently press the edge of the petal to make the outer end of the petal produce a certain arc, just like a real petal.
In order to make the flowers look more beautiful, you can try different papers, because too thick or too thin paper will affect the folded flowers.
The last step of flowering is to decorate the petals properly to make them look more natural and beautiful.
Of course, if you add branches and leaves, it will be more beautiful in a vase! Here is how to add branches and leaves to flowers.
The making of leaves is very simple. Just cut a piece of green paper in the shape of a leaf and fold out the veins.
These are the materials to be prepared. You can buy wire for flowers directly at the stationery store.
If you already have wire at home, you can also buy green adhesive tape (which is also necessary for making flowers) at the stationery store, and wrap the wire, and the effect is the same!
Put a circle at the top of the wire to help fix the wire in the flower.
Insert the wire into the bottom of the flower and stick some double-sided tape on the bottom of the flower.
Wrap green sticky paper around the wire and stick the flowers and branches together.
Although the green tape is sticky, if you feel that it is not sticky enough, you can also use double-sided tape to help.
That's why I have to stick some double-sided tape on the bottom of the flower.