Stair carpet, as its name implies, is the carpet laid on the stair tread brick. On the one hand, this kind of carpet is often made of fabric materials and other artificial composite fibers, so it has the effect of sound insulation and can also achieve the purpose of anti-skid. In addition, because the stair carpet is designed for the special size of the stairs, it should be as consistent as possible with the structure of the stairs themselves. For example, the common stairs may be spiral stairs, which are different from other stairs, and the specific situation is not as good.

First, how to lay the stair step carpet

1. Fixed strut for stair carpet laying:

Bury compression bar fasteners. There are two fasteners in the inner corner of each step, which are buried symmetrically with the center line of the stair width. The distance between the fastener hole wall and the stair tread and kicking surface is equal and slightly less than the carpet thickness; Cut the carpet length according to the sum of the actual widths of the tread and the kick surface in each step. If you consider replacing worn parts, you can reserve a certain length. Lay the carpet step by step from top to bottom. The end of the top carpet is nailed to the platform with slats. Cut a small hole in the carpet where the fastener is stepped on each floor, so that the fastener of the compression bar can protrude from it, then insert the metal compression bar into the round hole of the fastener and tighten the adjusting screw. For stairs with metal anti-skid strips, after the carpet is fixed, use expansion screws (or plastic expansion pipes) to fix the metal anti-skid strips on the edge of the external corner of the tread plate, and the nail distance is? 15~? 30 centimeters.

2, adhesive fixed stair carpet laying:

Cut the carpet according to the actual size; All adopt full scraping adhesive bonding; From top to bottom, use a rubber trowel to stick the adhesive on the tread and skirting surface of the stairs, properly dry and paste the carpet, and then roll it with a flat shovel to make the carpet smooth and dense; It is necessary to scrape the glue step by step and lay it step by step to avoid laying the carpet for a long time after scraping, and there is no place to stay; If it is necessary to install a metal anti-skid strip, it should be fixed with the compression bar; After paving the road? 24H？ Personnel are prohibited from entering or leaving.

3, fixed stair carpet laying:

Nail barbed boards on both sides of the inner corner between the stair tread and my kicking surface and leave them between the two barbed boards? 15mm？ Gaps, barbed wooden nails tend to internal corners; Carpet mat should cover the stair step and the external angle, and the coverage width on the step should not be less than? 15mm； Blanking the carpet according to the sum of tread width and kick width of each step and the appropriate reserved length; The end of the top carpet is nailed to the platform with wooden strips, and then laid layer by layer from top to bottom. At the internal corner of each step, tie the carpet tightly with a flat shovel and press it into the gap of three barbed plates on both sides; The reserved length part can be overlapped and nailed on the kicking surface of the last step.

Second, the stairs anti-skid means

Plastic laying method:

It is mainly used for public stairs or extra-wide stairs, made of plastic products, with obvious anti-slip protrusions, bright colors and convenient connection. It is only suitable for engineering ladders and not ideal for domestic ladders.

Anti-skid sand strip treatment method:

Anti-skid sand strips, stick 2 to 3 strips on the edge of the pedal, which can be used for anti-skid. The disadvantage is that it is suitable for sand removal after standing for a long time, which is unsightly and non-slip. When updating, it will leave glue, which is difficult to remove. Single color (paper yellow), not suitable for stairs, not suitable for home use.

Treatment method of inlaid metal strip:

Most of them are used on the stone surface at the edge of the pedal. This method has played an effective anti-skid role, but there is also a phenomenon of long-term trampling looseness. Once it is loose, it is difficult to handle it with glue, and there will be abnormal noise and dirt retention. Some places will be bright when you step on it, and some places will be black, which is very unsightly. Not suitable for family.

The above recommendation is the suggestion and installation method of stair tread carpet. Therefore, the suitable stair tread carpet can play a guiding role, and it can achieve the purpose of anti-skid and mute on the premise of protecting the stair tread floor tiles. So how to choose and install? What are the suitable materials? From the above, we can all get a more reliable answer, and we can also find that there are two installation methods of stair carpet, each with its own advantages.