Current location - Plastic Surgery and Aesthetics Network - Wedding planning company - Lighting knowledge sharing: indoor lighting installation skills, fast learning
Lighting knowledge sharing: indoor lighting installation skills, fast learning
As we all know, the purchase of lamps needs special attention. This part of the quality not only affects the whole decoration process, but also affects the decorative effect after the decoration is completed. Today, I introduced the skills of lighting installation, hoping to give you some help.

1. Installation sequence of ordinary lamps

(1) plastic (wood) table installation. Take out the lamp from the hole of the plastic (wooden) platform and put the plastic (wooden) platform on the surface of the building. Alignment of mounting holes of plastic (wood) table. Screw box hole, use machine screws to fix the plastic (wood) table firmly.

(2) Take out the wire drawn from the plastic (wood) table with an appropriate length for maintenance, cut the wire core, and then push it into the lamp holder. The core is higher than the plastic (wood) countertop. For the cable at the lamp line, after winding the magnetic core for 5-7 times, the wick is folded back and pressurized. Lay the layer with tape and black tape. Align the wound joint, the buckle on the flange, and the flange (hanging box, flat lamp) with the center of plastic (wood) and fix it with wood screws with the length less than 20 mm..

(3) Install the refrigerator chandelier. First of all, according to the installation height and quantity of lamps and lanterns, all suspension wires are twisted in advance. Ensure that the height of the bulb bottom from the ground is between 800- 1 100mm, and the coil will be looped after the messenger wire is completely lowered. Rinse tin and flatten it. According to the length of the messenger wire, break the flexible plastic pipe, cut the pipe end of the plastic pipe into two halves with a length of 20mm, and then put the messenger wire into the plastic pipe. Put it in the refrigerator, put the plastic pipes and lampshades at both ends of the hanging box cover on the plastic pipes, then pull the safety buckle, cut one end of the soft plastic pipe in half, heat and bond it, then press the lamp line on the hanging box, use the lamp holder as the screw hole, find the phase line and mark it properly. Finally, according to the installation method of plastic (wood) platform, the chandelier is installed and hoisted to.

2. The installation sequence is wall lamp

First, according to the shape of the lamp, choose a suitable wooden table or lamp holder, put the lamp on it, and keep the rest balanced and symmetrical. Then use an electric drill to open the holes and mounting holes on the circuit board, which are also on the bottom plate of the lamp. Open the mounting hole, pull the lamp cap wire out of the wire hole in the wood, connect it to the light box on the wall, wrap it tightly, and then insert the connector into the box. Wooden table or board to light bulb frame. Close to the wall, the wooden table can be fixed directly on the box ear with machine screws. If it is a wooden board, please fix it with an expansion pipe. So as to adjust that bottom of the wooden table (board) or the light bulb so as not to be skew. Then tighten the bulb with machine screws. The bottom of a wooden table (board) or lamp, the last light bulb, umbrella or lampshade. Install outdoor wall lamp board or waterproof rubber pad between lamp holder and wall, and drain water.

3. Installation sequence of lamps and lanterns

(1) Installation of combined ceiling lamp: according to the positions of embedded bolts and lamp holders, open the installation hole and outlet hole on the lamp tray with an electric drill, and install it when the tray is lifted, and the power cord is closely connected with the lead wire from the lamp. It should be as far as possible. Insert the light box. Then align the mounting holes of the plate with the embedded bolts, so that the plate is firmly fixed on the ceiling and tightened with nuts. Adjust the lamp holder, hang various decorations of the lamp, and install the light bulb and light bulb.

(2) Installation of chandelier: Lift the bulb and insert the embedded hanger into the lamp. After inserting the hook pin, open the tail in a dovetail shape and flatten it. Fasten the bandage on your head, straighten and push up the retaining ring on the upper part of the light bulb, fasten the inner connector, fix the retaining ring on the ceiling, tighten the fixing screws, adjust the light bulb on each lamp holder, and finally match the lampshade.

The chandelier is an advanced decorative lighting for the indoor ceiling. Its noble shape can highlight the grandeur of the house. The chandelier requires the house to have enough floors. Because the weight is a chandelier, it must be fixed firmly.

Installation method of chandelier

1, the chandelier is fixed

When fixing the chandelier, first draw the drilling point, punch the hole with an impact drill, and then insert the expansion screw into the hole. It is worth noting that because the load of the chandelier is generally greater than that of the ceiling lamp, the ceiling is fixed with a metal hanging plate or hook first, and then the chandelier base is connected, so the installation is more firm.

2, chandelier connection

Screw on the screw of the optical head, the base is installed and connected with the power cord, and the exposed part of the copper wire is wrapped with insulating tape. Then connect the boom with the base and adjust the appropriate height. Finally, you can install the chandelier lampshade and light bulb.

Precautions for installation of chandelier

1, please note that the chandelier cannot be installed too low.

The use of chandeliers requires the house to have enough floors. Whether the chandelier is installed in the living room or dining room, it should not be hung too short, so as not to hinder people's normal sight or feel dazzling. Generally, the boom can be adjusted to the height. The house is very low, with ceiling lamps, and the house is bright and generous.

2. Pay attention to the fixed safety of chassis.

The most basic requirement for the installation of lamps and lanterns is that they must be fixed. When in use, the light bulb should be installed according to the installation requirements of the light bulb. When the light bulb weighs more than 3kg, it should be installed with embedded hooks or brackets. Fix the fixing bolts directly on the roof.

3. Check whether the arm is firmly connected.

Generally speaking, the suspender of chandelier has a certain length of thread, which can adjust the height and has low utilization rate. In addition to carefully checking the installation, the chassis is also firmly fixed. Attention should be paid to the reliability of the connection of the light box hanging under the sling.