Current location - Plastic Surgery and Aesthetics Network - Plastic surgery and beauty - Does Honda Jade have a reversing radar?
Does Honda Jade have a reversing radar?
Honda Jade of Pacific Auto Network has a reversing radar. The reason why the reversing radar is equipped is: 1. When reversing, it can accurately measure the distance between the rear of the car and obstacles; 2. When reversing to a dangerous distance, it can give a rapid alarm to remind the driver to pay attention to braking; 3. Repeat the voice warning sound when reversing to remind pedestrians to pay attention.

Honda Jed reversing radar doesn't sound, Jed reversing radar doesn't sound. Honda Jade's reversing radar doesn't sound. It may be because Jed's radar alarm is very close, less than one meter away, but it is very accurate. It is also possible that the reversing radar is off, just press the P key in the lower left corner of the steering wheel to turn it on, or the screen, settings, and prompts are loud. If it's not these problems, let's go to the store for testing.

The following is the introduction of automobile reversing radar: reversing radar, namely "reversing anti-collision radar", also known as "reversing auxiliary device", is mainly composed of ultrasonic sensor, controller and display. The reversing radar is a safety auxiliary device when the car is parked or reversed. It can inform the driver of the surrounding obstacles through sound or more intuitive display, relieve the troubles caused by the driver's glance left and right when parking, reversing and starting the car, and help the driver eliminate the defects of blind spots and blurred vision.

Use Honda Jade low beam lamp. How to turn on Jed low beam is as follows: Low beam use: The low beam switch is on the control lever at the lower left of the steering wheel. First, turn the light adjuster on the left side of the steering wheel clockwise to turn on the light. At this time, all the lights on the dashboard are on. Then turn forward and turn on the low beam. Generally, pushing the joystick forward (without rotating) means turning on the high beam. At this time, the high beam sign will appear on the dashboard, and the low beam will not be displayed by default. Headlights have a special headlight switch. First, turn on the headlight switch. The switch for switching the low beam is the direction light handle under the steering wheel. The direction lights turn left and right, while the high beam lights turn up and down. The lower part is high beam, the upper part is low beam, the upper part is high beam, the upper part is high beam, the lower part is low beam, and the upper part is key switch.

Use of high beam: The way to turn on the high beam is that the crossbar on the left side of the steering wheel is the one that controls the turn signal. You can see that the front end of the crossbar can be twisted. * * * is divided into two files. Twist the width light switch, and then the low beam light. In the low beam state, you can lift the crossbar and press it, and the high beam will turn on.

Honda Jade high beam model, Jade high beam bulb replacement Honda Jade high beam model is H7.

The tutorial for replacing the jade high beam bulb is as follows: Step 1: Unplug the power socket of the bulb. When unplugging the bulb power socket, the strength should be moderate to avoid sending the socket wire or damaging the bulb plug.

Step 2: After unplugging the power connector, remove the waterproof cover behind the light bulb. The waterproof cover of the car lamp is mostly made of soft rubber, which can fall off with a little force.

Step 3: Take the bulb out of the reflector. Light bulbs are usually fixed with steel snap rings, and some models have plastic bases. When taking out the light bulb, you need to hold the steel wire clasp on both sides with your fingers, and then pull out the light bulb after releasing it.

Step 4: Put the new bulb into the reflector, aim at the fixed position of the bulb, hold the steel wire snap rings on both sides and push inward to fix the new bulb in the reflector.

Step 5: re-cover the waterproof cover, plug in the bulb power supply, and the replacement operation is completed.

Caution: Avoid direct contact with the bulb's glass shell. There are some precautions for replacing headlight bulbs that need the attention of the owner. When choosing a new light bulb, the owner should choose the right product according to the original light bulb model.

(Photo/Text/Photo: Pacific Auto Network Q&A called Beast)