You can refer to the following standards:
Film pasting workshop:
There must be no defects and sundries after window pasting, so professional installation must be carried out in a dust-free pasting room! The clean room not only has a closed glass door isolated from the outside, but also has a water mist nozzle and air conditioner to realize air dust removal, and the ground has a drainage ditch and special paint to further realize dust removal.
There is a dedicated workbench and articles in the room, which are neatly arranged. The installation effect under such a construction environment is by no means achievable by street open-air operation.
Architectural matters
Check whether the installation of window glass and the integrity of automobile glass are intact before pasting, so as to ensure the normal operation of subsequent pasting. Before pasting the film, the necessary parts in the car must be covered to prevent liquid from infiltrating. Sprayed cleaning liquid and lubricating liquid will affect decorative parts such as vehicle-mounted electronic equipment and interior seats. Clean the inner and outer surfaces of the window before pasting the film (focus on cleaning the inner decorative surface and glass sealant area). This is mainly to prevent dirt or other construction quality problems between the thermal insulation film and the window glass after pasting, and to ensure that the film can be combined with the glass.
Film pre-cutting: Measure the dimensions of the front and rear windshields with a ruler, and cut the film according to the measured dimensions.
Spraying installation liquid: dust spots can be avoided, edge corrosion can be reduced, viscosity required for solidification can be obtained, and construction effect is better.
Dry-baking and wet-baking for setting: firstly, dry-bake the heat-insulating film to make the heat-insulating film fully pre-shrink. In order to further improve the consistency of thermal insulation film, it is necessary to wet bake the thermal insulation film.
Extrusion of installation liquid: In the process of cleaning installation liquid with wiper, scrape the installation liquid between the thermal insulation film and the window glass as much as possible, which can reduce the drying time of the thermal insulation film and obtain better bonding effect, overall performance and visual effect. [3]
Specially installed automobile film: (1) There shall be no defects and sundries in the film, and there shall be no creases and air bubbles on the film surface. ⑵ At the top of the hem window, there should be only a tiny gap of 1-2mm, so it is not easy to be found by rough observation. (3) The black glaze area of the glass frame should be covered, without light leakage or warping, which is beautiful and harmonious. (4) There should be no visual ghost and water mark caused by uneven extrusion pressure and irregular extrusion path.
protective measure
Professional installation should take protective measures: to prevent scratching the paint surface, damaging the interior decoration, and short-circuiting the electrical appliances and audio in the car due to moisture; Avoid seat damage caused by window film installation and failure caused by accidental scratch or damage on the instrument panel surface.
chemical agent
Professional automobile film should use special film cleaning solution and installation solution, and dilute with pure water, so that the film and glass can achieve the maximum adhesive strength, and will not cause defects such as edge warping and delamination, and achieve long-term quality assurance effect.
Henan Yitong Automobile Products Co., Ltd. has become the general agent of many well-known brands in Henan, such as "Israeli special automobile glass window film-cold steel", "China CCTV cooperative brand-Xinhongbao customized automobile seat cushion and foot pad", "American high-end automobile solar film-master film", "American imported PPF- Gucci invisible car clothing" and "the leader of automobile functional perfume industry".
Pursuing the perfection of quality, customer satisfaction and employee development is our unchanging aim. Flourishing corporate culture is the source of enterprise development and promotion. With the business philosophy of high quality, high efficiency and good faith, we will resolutely implement the enterprise tenet of "customer first, quality first, service first, reputation first and employees first"; Make every effort to build a well-known brand in China auto parts industry, win the trust of customers with high quality and serve customers with high efficiency. First-class service team, advanced sales concept, committed to providing customers with comprehensive terminal sales solutions. Provide a comfortable, comfortable, worry-free and assured car post for the majority of car lovers. Enjoy the life of owning a car, starting with choosing Yitong.