Generally, the temple has a certain elasticity, so you can do it gently, a few times at a time.
It used to be the same when the frame was loose, hehe!
Question 2: Plastic full-frame glasses are loose and will slide down as soon as they bow their heads. How can they change back to their original shape? Your glasses should be rigid, right? So is mine. I don't think the frame is loose. As far as my situation is concerned, if my nose is not straight and my temples are a little long, I will try many ways to slip away. Later, I found that there is a kind of "anti-slip cover for glasses", which will not slip when worn on the glasses legs, even if it is exercised ~
An optical shop near my home sells a pair of 5 yuan, which is also available on Taobao. There are many colors, just buy transparent ones ~ If there is no one at home, you can consider buying them from Taobao. It's good. Now I don't even bow my head when skating. O(∩_∩)O~
I hope it helps you ~
Question 3: How to adjust the tightness of glasses? You can buy a set of special tools for repairing glasses in an optical shop. If the glasses screws are loose, you can repair them yourself. (5 1 spectacle net)
Question 4: The glasses are loose. How to adjust them away from the optical shop? There are many reasons why it is inconvenient to go to the optical shop. Please explain what made them loose, so as to facilitate the answer. Hello, it's just that the back foot cover is loose. You can pull the connecting part of the lens and the frame inward a little, and pay attention to the consistency of the two sides. If you bend the foot cover a little more, it should solve the problem. It should be noted that the strength should be determined according to the material of your glasses, and be careful not to damage them. Foot covers are hard to bend. What should I do? Also, to what extent? Well, that may be the material of your glasses. I really can't bend it. According to your requirements for tightness, you can only bend a little at a time. Adjust it slowly and give you a suggestion. The above methods are not good for your glasses. The next time you go to an optical shop, buy a rubber cover for the glasses frame from the clerk, which can help fix the glasses. I love sports and always use this. Very effective. Glasses seem to grow on my face. Not expensive, just a few dollars.
Question 5: The spectacle frame with plastic frame is loose. How to tighten the plastic workpiece is difficult to change after one molding. Please check whether there is a metal joint at the plastic joint for adjustment. If it is pure plastic, it may not be adjusted. I suggest you buy an alloy frame. Titanium alloy has memory function and light weight.
Question 6: What should I do if the glasses frame is loose? If it is a resin frame, bake it with a candle and bend it yourself. If it is metal, tighten the screws.
Question 7: What should I do if the glasses frame becomes loose? Fold the spectacle frame to expose the joint between the temple and the spectacle frame, and estimate the length here. Different types of spectacle frames have different lengths here.
Take out the protective pads of scissors, tables and chairs, and cut the protective pads into two strips, the length of which is the same as the size of the joint in [step 1].
Stick the cut protective pad on the joint between the glasses frame and the glasses frame, and trim the edge with scissors.
Reinforce the pasted protective pad with dry glue, and be careful not to let dry glue touch your hands and lenses.
The other side of the frame joint is also treated in the same way.
After the glue dries, unfold the folded frame. At this time, the frame has become much tighter. If it is too tight, you can trim it with scissors.
Question 8: How to adjust the tightness of the spectacle frame by yourself? Asking for tools, I am a little afraid that I can't adjust well. If I have a small wedge, I can tighten the screws on both sides of the frame. It is recommended not to break the glasses inside, because if I don't grasp them well, they will easily break. Small wedge optical shops generally have distribution. If not, you can use smaller scissors instead, but be careful when using scissors. Be careful not to scratch the lenses or hands.
Question 9: How to adjust the glasses frame at home? Introduction: After wearing glasses for a period of time, the frame will be deformed and loose. With the deformation of the frame, the wearer may be confused, deformed, dizzy and tired, so it is necessary to adjust the glasses regularly. So how do you adjust the glasses frame at home? Because the relative orientation of each person's face, nose and ears is different, glasses should be adjusted according to individual characteristics to make them elastic and comfortable to wear, and they should not be excessively pressed against the nose and ears. After wearing glasses, it is advisable to have no tenderness at the contact point and droop the glasses frame. The adjusted glasses should not only meet the national standards, but also meet the face requirements of the optician. After the assembly is completed, the frame glasses will be basically adjusted to meet the basic standards. But this basic adjustment of the frame is not aimed at the wearer's head, face and mental needs, so you can make fine adjustments according to your own practice after receiving the glasses. Because of the limited equipment at home, the choice of heater can be replaced by hair dryer and warm water heating. The width of the lens frame is not suitable for the head after wearing the lens, so you can consider adjusting the opening angle of the lens frame. The adjustment method is as follows: 1. Heat the pile head of the mirror frame with a heater (directly contact the lens when heating) 2. Wear the frame loosely: hold the frame with one hand, and the index finger and middle finger of the other hand are pressed against the horizontal eyebrow on the inner surface, and the thumb is pushed inward at the pile head on the surface of the frame to stop at the required angle. 3, the frame is tight, wearing a sense of squeezing: one hand holds the frame, the other hand holds the temple, and gradually pulls outward to the required angle. Note: The metal frame can omit the heating step. In the second case, the mirror face of the mirror frame is suitable, but the left and right lenses are uneven after wearing the lenses, and the unevenness of the temples can be adjusted. The adjustment method is as follows: 1. If the lens of the right eye is oriented higher after wearing glasses, the right temple will be raised or the angle of the left temple will be reduced, and vice versa. 2. Heat the pile head of the mirror frame with a heater (it will directly touch the lens when heated). 3. Hold the bracket with one hand and the foot of the mirror with the other hand, and gently pull it to the right angle in the required direction to stop. Note: The metal frame can omit the heating step. In the third case, the mirror face of the mirror frame is suitable, but the curvature of the back of the temple is inconsistent with the ear induction, and the fitting tightness is poor, so the length of the bending point of the temple can be adjusted. The adjustment method is as follows: 1. Put the frame on your face, find out the required bending direction and mark it. 2. Heat the vertically bent part with a heater, and then straighten it. 3. One hand is fixed on it, the thumb of the other hand is supported in the direction of the required bending point, and the index finger and middle finger are placed above the bending point, so that the bending point of the temple is bent downward and inward, and it is in warm contact with the ear after adjustment. After wearing: after wearing glasses for a period of time, the frame will be deformed and loose. With the deformation of the frame, the wearer may have blurred vision, distorted vision, dizziness, fatigue and other phenomena, so it is necessary to adjust the glasses regularly. Details: Precautions for use 1. Wear glasses with both hands. Wearing glasses with one hand for a long time is easy to deform them; 2. Don't wear glasses when doing strenuous exercise, so as not to bump and deform; 3. Take off your glasses when sleeping or lying on the table to avoid deformation of your glasses; 4. Wipe the glasses with a special mirror cloth, or clean them with water and detergent. Avoid using paper towels, handkerchiefs or wiping with clothes; 5. Don't put the glasses in a high-temperature environment above 50 degrees (such as sauna room and car windshield), so as not to accelerate the shedding of the lens film or the aging of the frame; 6, don't often do deformation demonstration of memory materials, so as to avoid fracture of connection or welding parts. In addition, the memory material will lose its memory function in the environment below-10 degree, even if it is bent, it will lead to fracture and deformation; 7. People who are allergic to metal should choose to form a material frame or install an anti-corrosion sleeve on the metal temple to avoid skin contact with metal; 8. When you don't wear glasses, you should put them in a box.