Ugg vamp is dirty. What should I do?
When cleaning ugg shoes. Wet a clean towel with water first, mainly to wipe the outside of the shoes. Clean with cold water or special cleaning brush. Please clean the particularly dirty places with an eraser first. Then gently scrub it with a brush several times. This can achieve the effect of deep cleaning. Then scrub with a clean sponge dipped in a small amount of detergent. Don't push too hard, otherwise it may damage the cortex. After cleaning. Shoes are stuffed with clothes hangers or newspaper balls to prop up the inside of the shoes and play a role in shaping. Dry in a ventilated and dry environment, but don't directly expose to strong light to avoid yellowing.
How to deal with the watermark on ugg shoes?
First, clean the sole to remove the stains on the ash layer of the upper.
Before launching the boots as a whole, brush the vamp with a wire brush to brush off dust and stains attached to the vamp, which is helpful for launching and cleaning the boots as a whole. Then wash the soles and shoes with a hard brush dipped in soap to prevent the stains on the soles from causing secondary pollution to the uppers.
Second, the overall water cleaning
Prepare a basin of warm water (the water temperature is 40-50 degrees Celsius), pour the leather cleaning agent into the basin and stir evenly (the amount of leather cleaning agent is about 20 ml). Soak all boots in water for 5 minutes, and then brush the whole upper with a soft brush. At this time, the multi-color watermark will slowly spread out. After brushing, the boots will dehydrate, and the watermark of dehydrated boots will basically disappear completely.
Third, rinse.
Prepare a basin of warm water (the water temperature is 40-50 degrees Celsius), add glacial acetic acid (the amount of glacial acetic acid is 3/1000 to 5/1000 of water) into the water, and stir well. Soak the dewatering boots for 10 minute, brush again after soaking, and dehydrate after brushing. At this point, the watermark on the boots has completely disappeared.
Fourth, fatliquoring.
Leather will harden after soaking in water, so we need to oil it to make it soft again. Prepare 300-400 ml warm water (water temperature 40-50 degrees Celsius), so that the boots are completely soaked. If there is too much water, the amount of softener will increase, resulting in waste. Add about 20% softener (60 ml -80 ml) in water and soak the boots in water for about 20 minutes. After that, the boots will dehydrate. Boots will obviously soften after dehydration. At this time, it is necessary to reshape the boots, which can be supported by shoe braces, and dry towels are stuffed in places that cannot be supported. After the boots are finalized, brush brush pile with steel wire, and naturally dry the shoes after shearing. After the shoes are shaped, the inserted towel is taken out, which is beneficial to speed up the drying of the shoes. Boots can't be dried with a hair dryer. If you use a hair dryer, the drying will be uneven and the watermark will be generated again. In order to prevent the watermark from being generated again in the drying process, the whole boot can be wrapped with a napkin, and even if the upper has floating color, the napkin will be inhaled, which will not cause color gathering.
V. Color maintenance
Boots will become lighter after soaking in water, so we need to add color to the boots for maintenance. If the customer doesn't ask for coloring, we don't need to take the method of coloring and brightening. At this time, we can use softener (softener can brighten the color) to brighten and maintain the boots. Stir the softener and warm water evenly according to the ratio of 1:5, spray it evenly on the vamp with a spray gun, and dry it naturally after spraying.
Six, fixation and velvet finishing
If the requirements are not high, we can complete the steps of color enhancement and maintenance, and the work of removing the multi-color watermark of boots can be completed. If the requirements are higher, you need to fix the color. For color fixing, we use the velvet color fixing hand agent (the color fixing hand agent can play a very good role in dust prevention and waterproof, and can also play a role in color matching) for spraying. The color fixing hand feeling agent does not need to be mixed with water, and is directly poured into a spray gun for spraying. After spraying, comb with velvet brush, and then dry naturally. Through the above six steps, the watermark produced by the color aggregation of snow boots can be completely removed, so that the boots are completely new. However, special attention should be paid to the following points during operation:
1, the clean water used to prepare the solvent must be warm water of 40-50 degrees Celsius, and the solvent can't function well if the water temperature is too high or too low.
2. Be sure to nap the boots before drying them after fatliquoring, so that they will be fuller after drying.
3. Boots must be dried naturally. You can't use a hair dryer to save time. If a hair dryer is used, a watermark will still be generated.
Maintenance of snow boots
If you buy snow boots without waterproof coating, you can use waterproof spray to increase the waterproof of shoes. Just spray the spray on the surface of the boots, then let it stand for about 10 minutes, and let the snow naturally dry the floor boots. Because the waterproof performance of boots is enhanced, the chance of boots being damaged by external stains can be reduced, thus prolonging the service life of boots. If you accidentally wet your boots, you must wait for them to dry before spraying a new protective coating. However, it is best to spray boots with waterproof spray within a few hours after purchase.
Matters needing attention in cleaning snow boots
1. Don't get your shoes wet. If there is any stain, please wet it with clear water.
2. Don't use all kinds of detergents containing bleach, only sheepskin cleaners.
After cleaning, the snow boots must be dried in the shade. Don't use any heating and drying methods, and don't expose yourself to the sun.
The cleaning process must be operated manually, not dry cleaning.
5. Sheepskin is soft. When you don't wear snow boots, don't forget to put the shoe supports inside the boots to keep them upright and fashionable.