Question 1: How to connect a broken wire? You can connect it directly, but the interface must be tightly connected, otherwise the connector will heat up and stick more tape on it

Question 2: Wires at home How to connect it when it's disconnected? I don't have any knowledge about electricity. Who can teach me? There are two colors in the wires, usually blue and red. Blue and blue are connected together, and red and red are connected together. However, you must wear insulating gloves or cut off the main power supply to ensure Safe preliminary work

Question 3: How to connect the cable TV cable if the wire is broken? The connection method of the cable TV cable is broken:

1. It is generally recommended to replace it with a new one Use signal connecting wires to ensure stable signal transmission; 2. You can also connect the ends of the two sections of wires to two signal plugs, and then connect the plugs to the signal connectors to achieve the connection, but this connection method may Causes signal transmission to be unstable, and sometimes the TV picture will be abnormal;

3. Simple method: peel off 0.5 cm of white plastic from the middle of the wire ends of the two sections of wire, make it as short as possible, and weld the central copper wire Okay, then put the stripped plastic on the outside of the core wire and try to keep it as it is; then twist the shielding net together (the solder cannot be soldered), and finally wrap it with insulating tape; the signal after this method is connected The transmission is the most unstable.

Question 4: How to connect a broken wire? Directly twist the core wires inside the two-end connectors together, but note that the outer core wires need to be tightly wrapped with high-voltage insulating tape, and both ends Wrap it with more than 1 cm to prevent leakage! Also, don’t operate with electricity!

Question 5: The plug and wire of the dehydrator is broken, how to connect it back? How to deal with the broken plug wire of the dehydrator:

1. Use wire cutters to peel off the broken point to expose the copper wire.

2. Use the docking method to wind the copper wire.

3. After the wiring is completed, restore the line insulation.

4. Power on and test the machine.

Question 6: How to operate the live wiring in the household circuit (how to connect the wire if it is broken). Several points should be paid attention to when operating: 1. Wear insulated shoes or stand on an insulated and dry object, such as a stool. , rubber pads, etc.; 2. Use tools with insulated handles, such as glue pliers and wire cutters with wooden handles (or rubber handles). During operation, hold the insulated part of the wire in one hand and the tool in the other. Do not touch the wall or ground with your body. and other electrical conductors; 3. When operating, be sure to separate the live wire and neutral wire first to prevent short circuit or accidental contact during operation; 4. Unplug all electrical plugs connected to the line; 5. Comparison of functional wiring that is entangled with each other. Reliable and with a large contact area.

Question 7: How should I connect the fan power cord at home if it is disconnected? One is connected to the timer and the other is connected to the capacitor.

Question 8: How to connect the broadband main line on the telephone pole if it is disconnected? If it is disconnected, contact the telecommunications company. They will pick it up. You do not need to do it.

Nowadays they are all optical fibers, which are fiberglass, not wires. You have no way to connect them.

Question 9: If the power cord is broken, can it be connected and used again? For high-power air conditioners and water heaters, the current is relatively large when working, requiring the entire wire to be replaced. Because the contact resistance at the connection is relatively large, it is easy to heat up. Small-power light bulbs, televisions, washing machines, etc. If the power cord is disconnected, it can be connected and reused

< p> Question 10: The cable is broken, how do you connect it? Oh wow, now you are unlucky. Use a crimping plier to crimp the copper core of the cable at the special connector and the broken cable. Shape and remove burrs, maintain and clean, and then Make the insulation layer, then connect the protective layer, and finally use heat shrink or cold shrink tubing as the outermost skin protection. Once the insulation test is passed, it can be restored.