Whether it is car film or building window film, we generally require professional technicians to carry out construction, otherwise many problems will easily occur, especially car window film, which is prone to failure. Many cars have wiring devices such as computers and navigators, which are prone to problems, so don't just think that you can film them. Without professional technicians and professional protection, it means that your car will cause more expenses and failures for its own reasons. This is of course the owner.
Master car film reminds you that car film has very strict technology and requirements:
1. Observe the installation of window glass:
Before construction, it is necessary to observe whether the window glass is installed in good condition and whether the automobile glass is complete, so as to ensure the normal work of subsequent film pasting.
2, the construction personnel dress, tool preparation:
The clothes of construction personnel can not only reflect the personnel management level of the construction unit, but also have an important impact on the construction quality. In the process of film pasting construction, the construction personnel must wear uniform tooling and fasten all buttons. This can avoid scratching the paint surface during construction and the clothes fibers flying to the construction surface.
Sharp tools make good work. Movies are no exception. Construction tools to be prepared include: wiper blade, pressure watering can, hot air gun (power and wind speed), cutting tool, absorbent towel, fluorescent lamp, adhesive tape masking film and glass cleaner.
3. Cover the necessary parts of the car to prevent liquid from infiltrating;
In order to ensure that the sprayed cleaning liquid and lubricating liquid will not affect the on-board electronic equipment during the construction of automobile thermal insulation film, and to ensure the initial state of the interior decoration to the greatest extent, it is necessary to cover the interior seat and instrument panel.
4. Clean the window glass to be constructed:
Clean the inner and outer surfaces of the window (focus on cleaning the inner decorative surface and glass sealant area). This is mainly to prevent dirt or other construction quality problems between the thermal insulation film and the window glass after pasting, and to ensure the perfect combination of the film and the glass.
5. Pre-cutting of the membrane:
Measure the dimensions of the front and rear windshields with a ruler, including the length and width. Select the type of thermal insulation film to be constructed from the tool rack and cut it according to the measured size of the windshield. Our Shaanxi Master window film is directly pasted by the computer, and the computer will cut out the corresponding window film according to your car model.
6. Dry baking and molding (pre-shrinking) of thermal insulation film:
In order to ensure that the plastic insulation film can fit the radian of the window glass more accurately and reduce various problems that may be found in the direct wet baking process, it is suggested to dry bake the insulation film before wet baking, so that the insulation film can be fully pre-shrunk.
7. Clean the outside of the windshield with glass cleaner and car wash mud, and spray the installation liquid:
The main purpose of spraying installation liquid is to ensure that the thermal insulation film can be better lubricated and moved during the construction of wet baking film.
8. Wet baking molding (pasting) of heat insulation film:
After the previous dry baking and setting operation, the shape of the thermal insulation film has basically matched the curvature of the windshield, but in order to further improve the adhesion of the thermal insulation film, it is necessary to wet bake and set the thermal insulation film.
9. Cutting plastic film:
In the process of cutting the plastic insulating film, the construction workers need to aim the fluorescent lamp at the cutting edge of the insulating film in the cab, because it can be more convenient for people outside the car to determine the cutting construction position.
10. Clean the inside of the windshield with cleaning liquid and spray enough installation liquid:
The purpose of spraying cleaning liquid is to avoid dust spots and reduce edge corrosion; The purpose of spraying installation liquid is to obtain the viscosity needed for solidification and better construction effect.
1 1. Remove the transparent protective layer on the film and stick the film on the inside of the windshield.
12. Use a wiper to squeeze out the installation liquid.
In the process of cleaning the installation liquid with the wiper, the installation liquid between the thermal insulation film and the window glass should be scraped off as much as possible, which can reduce the drying time of the thermal insulation film and obtain better bonding effect, overall performance and visual effect.
The effect check process is reassuring:
Usually, the master's film pasting process can be simply recorded as: spreading towels from the instrument, keeping clean-cleaning the glass-cutting the film-setting a heat insulation film on the outer glass of the window-cutting corners according to the shape of the glass-cleaning the inner glass-formal film pasting-boiling water, blowing corners with a hair dryer-and finally cleaning.
It is recommended that your car be overhauled to avoid more serious failures. I hope my answer can be useful to my friends.