1, decorative:

The artistic effect of color is diverse, dynamic, textured and spatial. At the same time, the optical fiber is flexible and can freely guide the light to the required position according to different ideas. Very personal charm.

2, high security:

Photoelectric isolation is realized, and there is no electric energy and heat energy in the optical fiber part, so it can be safe to contact the luminescent fiber under any circumstances.

3. Health and environmental protection:

The light emitted by fiber-optic lighting is cold light that filters infrared rays and ultraviolet rays. The light is soft and pure, does not generate heat, reduces the environmental burden of the air conditioning system, and realizes high efficiency and energy saving while protecting vision health. The optical fiber material itself is also environmentally friendly and does not contain any form of volatile substances.

4. Long service life and easy operation and maintenance;

The service life of optical fiber itself is more than 20 years, and it can be installed once and used indefinitely. The switch is easy to operate and maintain. In case of moving, it can also be reused in the new house after demolition.

Installation steps and precautions of starry sky canopy

1, Selection of ceiling materials for optical fiber starry sky

Polyester fiber sound-absorbing board is usually used as ceiling material for theater decoration, and its advantages are as follows:

(1) optical fiber is easy to wear;

(2) convenient construction, simple corner treatment, seamless splicing, free chamfering and splicing of different shapes;

③ Good sound absorption performance;

(4) Various colors can be selected without post-treatment;

⑤ Environmental protection and non-toxic.

2, optical fiber size and quantity configuration

According to the length-width ratio of the installation room, a considerable number of optical fibers are configured, and the number of optical fibers with different lengths and diameters is reasonably distributed. Too dense or too sparse will lead to unsatisfactory final results.

When threading optical fiber, thread the shorter optical fiber near the light source machine and the longer optical fiber away from the light source machine. For example, 1 m optical fiber passes through the position near the light source machine, and then 1.5 m and 2 m optical fiber in turn, with the same length. Optical fibers with different diameters are distributed among them, and super bright stars, bright stars and micro bright stars present realistic starry sky. Starlight flashing can make different colors appear alternately, and can also locate a certain color.

Step 3 Install optical fiber

This determines the final effect. On the home page, mark the position that needs to be drilled on the polyester fiber sound-absorbing board, and the star arrangement position can be DIY into your favorite constellation. Then drill holes at the marked place according to the opening size corresponding to the optical fiber, and then penetrate the optical fiber into the polyester fiber sound-absorbing board.

Centering on the placement position of the machine, put the optical fiber down from the top of the ceiling, pass through and leave a section, and fix it by dropping a drop of epoxy resin glue at the joint between the optical fiber and the sound-absorbing board. Resin glue should be slowly dried for more than 2 hours.

4. Installation of light source

The light source must be installed on a ventilated, dry and easy-to-maintain ceiling. If the ceiling is fully enclosed, a movable access door should be set at the position where the light source device is placed to facilitate the placement and maintenance of the light source device.

5. Specific installation steps

① Reserve a 220V power cord on the top surface, and prepare an inclined three-eye 10A socket panel. Corresponding wall switches shall be reserved on the wall surface.

(2) On the top surface, lay a keel (wooden keel and light steel keel can be used) with a height greater than 8CM in advance.

(3) After the keel is laid, the ceiling material of optical fiber (such as gypsum board) should not be installed first, but should be put on the ground after being approved. After the optical fiber is installed in place, the flat-fell seam of gypsum board should be reserved with a width of about 5CM. Don't batch it, and then fill it after the gypsum board is installed on the ceiling.

(4) The optical fiber starry sky installer will install the optical fiber starry sky on the gypsum board on the ground. After the ground installation is completed, the carpenter will install and fix the corresponding gypsum board on the ceiling keel.

(5) After the ceiling installation is completed, the painter will caulk the gypsum board, which can be painted or painted as needed. After the paint or coating dries, the excess optical fiber will be cut flat, which is more effective.

⑥ The light source generation and control system should be installed in a ventilated, dry and easy-to-maintain position on the ceiling. If the ceiling is fully enclosed, a manhole should be opened at an appropriate position in the ceiling to facilitate the placement and maintenance of the control device.

6. Tips:

(1) The module is installed with power on all the way, and check whether the optical fiber lamp on the module emits light normally;

② The power cord is reserved at the inner side of the edge top, which does not affect the overall beauty.

(3) The installation of the keel shall ensure that the included angle is 90 degrees, because the module is a standard right angle, so in order to avoid irregular fitting, the preliminary work should be done well.