Current location - Plastic Surgery and Aesthetics Network - Wedding supplies - How to hook a hat
How to hook a hat
The steps of hooking the hat are as follows:

Step 1: Tick one short stitch to 20 stitches from 15, and tick back and forth in each row. When crocheting, only half a braid hole is hooked and 50 rows are hooked. Better put them on your head and compare them.

Step 2: Fold the two sides in half and connect them with Afghan short needle crochet method. This stitch is as shown in the figure, all the needles are stirred up, and then two needles are brought out at a time when returning.

Step 3: After weaving to a certain height, leave the thread end long for sewing. After sewing the reference picture, turn the hat over.

Step 4: After the hat is woven and sewn, sew ornaments on it. Wool balls are made by hand winding about 50 times. Tie the thread in the middle, cut both sides and trim the burrs.

Method 2: First, hook the hat from the edge, and demonstrate the 16 pin lock (width is about 10 cm) from the A color line. We turn the surface hook back and forth. 1 thread: short needle and thread without or without hook; The second line: take off the half needle without adding a line of short needles and without reducing the hook; After that, repeat the hook method in the second line until it reaches a length of about 44 cm (this length can be flexibly determined according to the head circumference of the hook fabric, and the size can be tried around the head, and the hook piece is elastic).

Then fold the hook piece in half, aim at one needle one by one in turn, pick two and a half needle hooks together, and pull out the needle for sewing. Then start to hook the cap body, circle 1: pick the needles in the thread, the total number of needles picked should be a multiple of 4, and the demonstration model should pick 64 needles (everyone should calculate whether it is necessary to add needles evenly according to the specific number of rows); The second lap: change the color line B, take off the half needle without reducing the hook, and finally take off the half needle 1 short needle, and switch back to the color line A and pull it out.

Cycle 3: Pick the lower half needle, hook three short needles in turn, and the fourth needle picks the first half needle of the long needle left by the A line of 1 (the first half needle of the long needle in the same line as 1, hereinafter referred to as long needle), repeat the hook method of these four needles, remove the hook, and finally pull it out with the B line (the method is the same as the second cycle); Cycle 4: Repeat (1 long needle, take off the half needle, and hook three short needles in turn) to complete the cycle, and finally pull it out by changing the A color line (the short needle I mentioned later needs to take off the half needle hook).

Loop 5: Repeat (1 is short, 1 is long, and 2 is short) a complete loop of the loop hook. This rule will be repeated later until the required cap height is reached and the model hook reaches a height of about 13 cm. Pattern rule: first, unhook the lines of two colors alternately, hook the line A and hook the line B; Secondly, each row only needs to find the position of the long needle and hook it to the left of the previous long needle, and the other needles are hooked on the short needle; So we don't need to remember the specific hook method, just look at the lines to hook it.

Finally, we entered the top of the hat. Cycle 1: line B (if you happen to be line A, use line A), repeat (2 short,1long needle, the fourth needle is not hooked) to tick a complete cycle; The second lap: repeat (1 long, 1 short) a complete lap (that is, this lap skips 1 and the short needle is not hooked); The third lap: all the long stitches are hooked in this lap (the short stitches of 1 are not hooked). After this loop is hooked, the thread is broken, the thread end is inserted into the sewing needle, and the remaining braid is taken out from the top of the hat. This beautiful mosaic flangeless hat is finished!