Analysis of the method of making copper bracelets teaches you how to make jewelry in a few simple steps. Clothing collocation is a science, and wearing personality also enhances personal charm. Fresh and playful styles make you the most beautiful scenery in spring, so how can you wear them to make women more beautiful? Now share the analysis of how to make copper bracelets, teach you how to make jewelry and turn you into a fashionista!

Analyze how to make a copper bracelet. Simple steps teach you how to make jewelry 1. If you want to DIY your own copper bracelet, the process is not difficult, just prepare the necessary tools. A small copper wire can easily make a beautiful bracelet. Moreover, jewelry needs to be cleaned regularly to avoid blackening.

We can often see many copper bracelets worn by female friends in the street. Do you know how to do it? Many people have made this kind of bracelet with exquisite shape and beautiful picture, and only those skilled craftsmen can make it.

In fact, as long as you master the correct production skills, you can easily become a jewelry artist. Next, I will give you a detailed introduction on how to wind a beautiful and simple' fashion bracelet'. Starting from the initial single thread, beginners can have a deeper understanding of the steps before and after.

First, analyze the specific production steps.

First of all, the first step is to prepare the necessary tools, including copper wire, scissors, round pliers and electric glue hammer.

The second step is to select the specific thickness of copper wire according to the size of the design pattern. If it is a bracelet, it needs to be thicker, and it needs to be cut out to be longer, so as not to make the back line insufficient. If there is any left, clip it off and straighten the interface.

Step 3: Wrap the cut silk thread around the model rod and compare the sizes.

Second, what should I do if the copper bracelet turns black?

Like silver jewelry, copper jewelry will be slowly oxidized by oxygen in the air after being worn for a long time. Or it is polluted by some strong oxidizing substances and turns black instantly. Therefore, we need to clean our ornaments regularly. Toothpaste is a very good decontamination helper. Because it contains a lot of calcium carbonate particles, it is easy to remove the oxidized substances hidden in the cracks in the process of cleaning the friction.

So you just need to take a soft toothbrush and gently brush it clean. After washing, you can gently wipe off all the remaining moisture with a silver cloth.

The analysis of the production method of copper bracelet teaches you how to make jewelry in a few simple steps. First of all, according to your own ideas, design the pattern you want, either simple or complex. After designing the sketch, use the computer to draw the accurate design drawing. Then began to produce wax board. Wax boards should be carved by hand. After the wax plate production is completed, the silver plate production will begin. Silver plate mainly adopts the method of lost wax casting, and finally the production of rubber film! The method of silver plate pressing is adopted here.

It should be noted that a clean wax injection machine should be prepared, but the temperature of wax in the wax injection machine should be controlled between 70℃ and 75℃. The wax liquid at this temperature should be carefully injected into the plastic mold, and the perfect wax mold should be taken out after cooling.

Here, molten metal is mainly used for casting, and the pouring amount of metal is calculated according to the ratio of wax tree weight to metal density. How to make wax trees? Weld each wax ring to a new wax tree by hand. Then we have to calculate the weight of the wax tree. Weigh the rubber chassis first, and then weigh the planted wax tree again. The weight of the wax tree will be obtained by subtracting the results of these two weighing.

Put the wax tree together with the chassis on the stainless steel cylinder, and then slowly pour the corresponding weight of fine gypsum slurry along the cylinder wall, and the height should not exceed the wax tree. After vacuum storage for 6 to 12 hours, the gypsum solidifies and can be baked after solidification, and a perfect gypsum mold can be obtained. Then, the prepared molten metal is injected from the nozzle. After molding, the metal is taken out and professionally cleaned, and the perfect bracelet is obtained.

Finally, it needs to be polished and polished, and then the surface is clean and flawless. Check the bracelet carefully to ensure the quality!