Current location - Plastic Surgery and Aesthetics Network - Plastic surgery and beauty - Methods and steps of car foil tutorial Matters needing attention in car foil
Methods and steps of car foil tutorial Matters needing attention in car foil
Installation skills of solar film Automobile solar film, commonly known as explosion-proof film, refers to the film attached to the surface of automobile glass. It not only has explosion-proof function, but also can insulate heat and avoid light. Usually, a special polyester film is used as the base material to make a high-quality explosion-proof film. The film itself has strong toughness and is equipped with special pressure-sensitive adhesive. In case of an accident, even if the glass is broken, it can be broken without hurting people. Now the automobile explosion-proof membrane also has the function of one-way perspective and glare reduction. Introduction to the steps of car film pasting: 1) First, spray clean water on the inside of clean glass, then tear off the protective film of the solar film, spray clean water on the coated surface, and then select a suitable film. 2) Stick the solar film on the glass, and then cut along the edge. 3) After pasting, there will be many bubbles on the glass. 4) Extruding with a plastic scraper. 5) baking and setting. 6) Make some details. 7) Finally, clean the car body. Tip: After pasting the film, you can put a reminder sticker in a prominent position to warn the owner not to roll down the window for three days. Because the solar film is stuck on the inside of the window, clean water should be sprayed in the car before sticking the film to let the dust particles sink as soon as possible. When pasting film, although the temperature inside the car is high, do not use the air conditioner inside the car. Precautions for avoiding sand particles in automobile film: (1) Many construction workers will directly use tap water in their work, but there are many impurities or sand particles in the tap water pipeline, which should be avoided without filtration or precipitation. (2) Dust Many shops do not have special film pasting rooms. Cars whizzing by will stir up a lot of dust, and sometimes there will be dust when the wind speed is high. So when there is no filming room, all the doors should be closed before filming. (3) Work clothes When the transparent part of the thermal insulation film is disassembled, a lot of static electricity will be generated. So avoid wearing woolen cloth or clothes with cotton wool when sticking stickers, because static electricity will attract cotton wool or wool on clothes to the film. (4) The film that has been cut on the surface of the film is generally placed on the car mat, chair cover, or on the roof and engine compartment cover to make its internal and external environment unclean. At the same time, the dust attached to its surface will also be attracted to the film when it is uncovered due to static electricity. Therefore, the transparent film must be cleaned or sprayed with water to prevent dust and sand. (5) Chair covers or decorations. Some chair covers or decorations are made of rabbit hair, fox hair or cotton. Due to static electricity, you should also pay attention when uncovering the film. Moreover, when uncovering the film, it is necessary to avoid being too close to the object to prevent the dust on the object from being electrostatically adsorbed. (6) When someone opens the door to open the film or wash the glass, try to be careful not to let people outside the car open the door. Forcibly opening the door may cause the outside air to enter quickly and bring a lot of dust or sand. (7) The air-conditioning wind speed is too high, and it is hot in summer, which is the peak season for sticking heat insulation film. Because of the high temperature in the sun or in the car, it is inevitable to open the air conditioning film in the car. However, when opening the film, the air conditioning wind speed should be adjusted to the minimum. After uncovering the film and sticking the glass, increase the wind speed. (8) The bottom of the sprinkler is not clean. When in use, the sprinkler is generally placed on the ground, on the mat or on the chair cover, and the bottom is generally unclean. When you open the film, if the nozzle shakes back and forth on the film, its bottom will exist. Sand and pebbles will fall on the film, so wipe the bottom of the nozzle before use. (9) After the transparent film is disassembled by hand, you must pinch the heat insulation film with two fingers, and fingerprints and sand grains will appear on the pinched part. The difficulty is to control the film as little as possible in principle. (10) The wiping method is incorrect. When cleaning the glass, the wiper cannot be wiped casually, or the wiper is intermittent, or the result is unknown. There is a fixed wiping method, otherwise it will bring sand. (1 1) When the washing wiper cannot reach (12), the next step after sticking the film is the wiping direction. Water can be scraped from top to bottom, from left to right or from right to left. However, in order to prevent the downward flow of water from causing sand particles to come down, a large amount of water cannot be scraped from bottom to top.