1. What should I do if the sealing strip of the refrigerator door is not tightly closed with the freezer frame?
Leaving the freezer door open has always been the focus of everyone's attention. Indeed, the consequences of lax cupboard doors are also very serious. If the magnetic door of the refrigerator is not well sealed, it will directly affect the air leakage of the refrigerator, resulting in poor refrigeration effect and increased power consumption, and it is also easy to cause the compressor to be repeatedly started and burned.
So why is there such a problem with the freezer door? According to experts, there are several reasons for this problem, each of which is very different. When installing a new magnetic door seal, you can wrap the refrigerator door of the same size around the door lining, paste it on the inside of the door after passing the proofreading, aim at the original position, and tighten the screws with a screwdriver.
Iron filings or metal powder are adsorbed on the magnetic door seal, which makes the door of the box not close tightly. Even if the door seal is worn, you can paste white paper where there is no iron filings, sweep the iron filings on the paper with a brush or rag, and then lift the white paper, and the iron filings will fall off.
Due to wear and corrosion, the fit gap between the door shaft and the shaft cavity increases, and the door leans to one side. If adjusted according to the above method, the door seal can be softened and raised by heating the door seal with a blower, or the door seal can be raised by adding waste plastic. If it is severely hardened, wrinkled, shrunk or fallen off, the door sealing strip can be replaced and eliminated. The method is as follows: First, remove the air chamber of the door sealing strip to be replaced.
When installing tapping screws, pay attention to adjust the tightness of the door sealing strip at any time. Thin pieces of paper can be naturally caught in the crack of the door, and a certain pull-out resistance is qualified. Or use a flashlight to put it in a box for lighting verification. If there is no light transmission, it is qualified.
If the door seal is slightly deformed and the plane is not straight, loosen the screw fixing the door seal, put white rubber on the plane with cracks, and then tighten the screw to eliminate the cracks. If the closed back door is not parallel to the box, the bracket for fixing the door can be adjusted to be parallel to the box. You can also put some soft plastic foam in the gap of the door seal to solve the problem of lax door seal.
If there is no match5ming product, use the door seal. Before replacing it, soak the door seal bent due to binding in hot water at 60℃ for 5 minutes, then take it out and put it on a flat plate for straightening, and then cut it into four sections according to the original size of the freezer door with a blade, with the two ends of each section at a 45-degree angle. After the four corners of the end are heated and melted by an electric soldering iron, the door can be fixed.
Second, the steps to replace the refrigerator door seal
First, take out the magnetic stripe in the old door seal. First, it can be adsorbed on the refrigerator body to avoid the possibility of damage or breakage. Then, remove the old door sealing strip and replace it with a new one. Finally, insert the magnetic stripe just taken out into the new door seal.
Generally speaking, it is caused by the following reasons:
1, door sealing strip is aging. Due to the repeated opening and closing of the refrigerator door, the sealing strip of the refrigerator door is almost always under stress. If this state is maintained for a long time, the door seal is easy to age and deform, resulting in the refrigerator door not being closed tightly.
2. The suction of refrigerator door is not big enough. At present, most refrigerators on the market adopt drawer design, which solves the problem of opening and closing doors for children. However, once this technology is not too hard, it is easy to cause the refrigerator door to loosen and it is difficult to tighten the refrigerator door.
The refrigerator is not well maintained. In fact, refrigerators, like people, should always be properly maintained. If it is not properly maintained for a period of time, it will make it sick and the refrigerator door will not close tightly.
It is very important to clean the refrigerator correctly. For the treatment of the refrigerator, not only the inside of the refrigerator should be treated, but also the outside of the refrigerator should be cleaned frequently. Otherwise, once too many stains are deposited on the outside of the refrigerator, the refrigerator door will not be closed tightly, and the door seal should be cleaned regularly and correctly.
There are many reasons why the sealing strip between the refrigerator door and the freezer frame is not tight. From the above introduction, we can find that the most common reason is the aging of the sealing strip of the refrigerator door. In this case, we need to find a suitable substitute and replace it with the help of professionals. Of course, considering the particularity of the scene, we also introduced the specific and detailed replacement steps for everyone. Interested friends can focus on the graphic content in the second half of the above.
Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp； Wb, you can get it for free ~