Current location - Plastic Surgery and Aesthetics Network - Plastic surgery and beauty - The working process of mobile phone can be roughly described as: mobile phone 1→( )→ mobile phone 2.
The working process of mobile phone can be roughly described as: mobile phone 1→( )→ mobile phone 2.
First, the mobile phone goes to the base station through the telephone exchange, and then to the other mobile phone.

Second, the reason why mobile phones can communicate with each other is the result of the cooperative work of radio frequency part, logic part and power supply part.

(1) RF part

Generally, the RF part consists of a signal receiving part and a signal transmitting part.

When a mobile phone receives a signal, it first separates the received RF signal of 935-960MHz from the received RF signal through U400 and SW363, so that the transceivers do not interfere with each other. Input the fourth pin of U400 and output the fifth pin, and enter the receiving front-end loop.

The working state of U400 is controlled by the third pin potential, which in turn is controlled by TXON and RXON signals sent by CPU. The RF signal passing through the antenna switch is filtered by the band-pass filter FL45 1 and then sent to the high-frequency amplifier Q4 18 for amplification. The output of Q4 18 is filtered by FL452 and sent to Q420 mixer for mixing. The local oscillator signal is generated by RXVCO, filtered by FL453 and sent to the base of Q420 for mixing, and the difference is taken. The collector of Q420 outputs an intermediate frequency signal of 153MHz, and after filtering by FL420, a pure signal of 153MHz is obtained. Now it is amplified by Q42 1 and sent to 3 1 of U2065438. The intermediate frequency signal of 153MHz and the carrier signal of 153MHz are demodulated within 32D53 to generate RXI and RXQ analog baseband signals, which are sent to U50 1 14# and/kloc-through 46# and 48# of U20 1. After A/D conversion in U50 1, it is sent to digital signal processor for further processing.

The carrier wave of 153MHz is a 306MHz oscillator circuit composed of 4 1#, 42# and 43# of U20 1, which forms a wave signal of 306MHz, and after two frequencies, forms the carrier wave of 153MHz. In the transmitting part, TXIN, TXIP, TXQN and TXQP signals output from 2 1#, 22#, 23# and 24# of 50 1 enter 6 1#, 62#, 63# and U20 1. U20 1 6#, 7# and 10# are externally connected with a VCO of 2 16MHz to generate a carrier signal of 2 16MHz, which is divided by the frequency divider in U20 1 to generate the transmission of 108MHz. Four modulated signals are modulated by 108MHz carrier in U20 1 and output from the 4 # pin of U300.

U300 completes the phase smoothing frequency between the transmitted sampling signal and TXVCO, and takes the difference to obtain 108MHz signal and TXIF input of No.4 to generate phase discrimination error voltage, which is output from the eighth pin to control the capacity of varactor CR300 and change the oscillation frequency of TXVCO. The 890-9 15MHz transmission signal output from the C pole of Q300 enters the power amplifier Q302 after being amplified by Q30 1 and pushed by Q302. The amplified signal enters the 1 pin of the antenna U400, and then is emitted from the 4# transmitting antenna of U400.

(B) the logical part

In the logic part, the received RXI and RXQ analog baseband signals are D/A converted, decrypted and adaptively equalized in the modem U50 1, and then the digital baseband signals are sent from 6# of U50 1 to 10# of the CPU, where the channel is decoded.

After removing the error-correcting code source and obtaining the real control information, the recovered voice data flows through the data line and the address line and is transmitted to the voice equipment U80 1 for decoding. The generated digital voice signal is sent from 78# of U80 1 to 8# of PCM decoder U803. The digital voice signal is decompressed and A/D converted in PCM decoder, then the received signal and volume are adjusted by digital volume locator, and then the analog audio signal is output from 4# of U803 to 6# and 2 1# of U900. After the ringing signal of the 6# input is amplified by the internal ringing driver, the 4# and 5# outputs of U900 drive the ringer to send the inter-tone signal, the 2 1# input, and the amplified voice signals from 19# and 20# output drive the receiver to sound.

When the user is talking, the voice is sent to the 9# terminal of the power integrated circuit U0- after acoustic-electrical conversion by the receiver, and the amplified analog audio signal is output from the 10# terminal after internal audio amplification. The signal is sent to the PCM codec U803 of 18#, and the pulse code modulation is completed inside U803. The PCM signal output by 13# is sent to the 89# speech encoder of 80 1, and the speech data line and address line are fed into U80 1, and the speech data stream is loaded into the central processor U70 1. After the channel coding of the voice data stream is completed in U70 1, the 1 1# after U70 1 is sent to the 4# of the modem U50 1, and the signal is subjected to D/A conversion and encryption processing in U50 1.

(3) Power supply part

As for the power supply, once the battery is installed in the mobile phone, the electronic Q999 will be turned on; At the same time, 48# of 32D54 is connected to the positive pole of power supply. At this time, press the power button again, and the 24# of U900 will become low level. The four voltages stably output by U900 are R275V, L2.75V, R4.75V and L5.0V. The 30th # generates a reset signal, and the 27th # generates an application start signal.

The 13MHz clock oscillator consisting of 32D53 and 13MHz crystal and transformer diode * * generates the 13MHz clock, which is shaped and amplified in the 32D53, and then output from 59 # to 17# of the buffer interface circuit U703, and then sent to 57 # of the CPU from 37 # of U703. In addition, the collector voltages of Q202 and Q203 are both 2.75V, which supplies power for the receiving or transmitting circuit inside 32D53. L5.0V sent by No.3 U900 supplies power to the negative voltage generating circuit.