1, the lamp beads must be multicolored, such as RGB full color.

2, need IC controller

Now there is a new product, you can have a look, that is, the lamp bead integrates IC controller, just stick the lamp bead on the lamp board, link the controller, and drive it with 5V voltage, and it can change any color!

The light bulb looks like this. The biggest one is IC68 12 controller, and the rest are LED chips.

The picture shows the lamp beads we produced.

5050 built-in SK68 12 has intelligent reverse connection protection, and the reverse connection of power supply will not damage IC.

SK68 12IC control circuit and LED point light source share a power supply.

The control circuit and RGB chip are integrated in a 5050 package to form a complete external control pixel.

Built-in signal shaping circuit, any pixel receives the signal and outputs it after waveform shaping to ensure that the line waveform distortion will not accumulate.

Built-in power-on reset and power-off reset circuits.

The three primary colors of each pixel can achieve 256 levels of brightness display, and complete the full true color display of 167772 16 colors, and the scanning frequency is not less than 400 Hz/s.

Serial cascade interface, which can receive and decode data through signal lines.

When the transmission distance between any two points is less than 5 meters, there is no need to add any circuit.

When the refresh rate is 30 frames per second, the number of cascades should not be less than 1024 points.

The data transmission speed can reach 800Kbps.

The color of light is highly consistent and cost-effective.

Main application fields:

LED full-color luminous character light string, LED full-color module, LED full-color soft light bar and hard light bar, LED guardrail tube.

LED point light source, LED pixel screen, LED special-shaped screen, various electronic products, electric lantern.

● The control circuit and RGB chip are integrated in a 5050 package to form a complete external control pixel.

Built-in signal shaping circuit, any pixel receives the signal and outputs it after waveform shaping to ensure that the line waveform distortion will not accumulate.

● Built-in power-on reset and power-off reset circuits.

● The three primary colors of each pixel can display 256 levels of brightness, and complete the full true color display of 167772 16 colors, with the scanning frequency not less than.

400 Hz/sec.

● Serial cascade interface, which can receive and decode data through signal lines.

● When the transmission distance between any two points is less than 5m, there is no need to add any circuit.

● When the refresh rate is 30 frames per second, the cascade number of low-speed mode shall not be less than 5 12 points, and that of high-speed mode shall not be less than 1024 points.

● The data transmission speed can reach 800Kbps.

● The lighting color is highly consistent and cost-effective.

5050 built-in IC68 12 is an intelligent external control LED light source integrating control circuit and light-emitting circuit. Its appearance is the same as a 5050LED lamp bead, and each element is a pixel. The pixel includes an intelligent digital interface data latch signal shaping and amplifying drive circuit, a high-precision internal oscillator and a 5V high-voltage programmable constant current control part, which effectively ensures the high consistency of the color of the pixel light. The data protocol adopts the communication mode of single-line return-to-zero code. After powering on and resetting the pixel, the DIN terminal receives the data sent by the controller. First, the transmitted 24-bit data is extracted by the first pixel and then sent to the data latch inside the pixel. After the remaining data is shaped and amplified by the internal shaping processing circuit, it is forwarded to the next cascaded pixel through the DO port, and the signal is reduced by 24 bits for each pixel transmitted. Pixels adopt automatic shaping and forwarding technology, so that the number of cascaded pixels is not limited by signal transmission, but only by signal transmission speed requirements. LED has the advantages of low voltage driving, environmental protection and energy saving, high brightness, large scattering angle, good consistency, ultra-low power and long life. Integrating the control circuit on the LED makes the circuit simpler, smaller and easier to install.