Question 2: How to bend the aluminum-plastic plate? Hello!
You can cut the aluminum-plastic plate according to the specific size, and then trim a line about 1.5 mm deep on the back of the aluminum-plastic plate according to the size to be bent, and then you can bend it. Be careful not to fold it too much to avoid the aluminum-plastic plate from breaking. The trimming depth of the trimming knife should not be too deep or too shallow. If it is too deep, the aluminum-plastic plate is easy to break and the angle is uneven. If it is too shallow, it will have no effect.
If bent into an arc, the aluminum-plastic plate will naturally bend as long as the aluminum layer on the back of the aluminum-plastic plate is torn with a vise.
Mu Feng's practice is easy to form edges and corners on the surface of aluminum-plastic plates. It is best to use detail workers or wood squares as the skeleton, and then lay a layer of 3~9 cm wooden boards as the bottom. If you paste it again, the fillet will be smooth.
You can contact online if you need it.
Question 3: Can the aluminum-plastic composite board bend 90 degrees? We are Guangzhou Window of the Future New Materials Co., Ltd., specializing in the production of aluminum-plastic plates for more than ten years.
In the process of aluminum-plastic plate material processing, it is a common processing method to bend at a right angle of 90 degrees after grooving, and it is no problem to bend at a larger angle, that is, more than 90 degrees.
Of course, if there is no slot on the back, the surface of the flat plate may be broken after bending 90 degrees directly.
For details, please consult 800830 1575. We can provide this service.
Question 4: How plastic is the aluminum-plastic plate? How to stand up and put it down for a while? Is the plasticity, strength, hardness and toughness of aluminum-plastic plate good?
Stand upright and cannot be deformed.
Question 5: Can an aluminum plate with a thickness of 1mm be bent? I answered another netizen's similar question before, but he asked about 5 mm thick aluminum plate, and the answer was the same. Copy it for your reference.
Can you bend it?
First of all, the state is the most important. The state of aluminum plate is divided into full hard, semi-hard and soft state (usually soft state is called O state).
The effect of full hard bending is basically not good (aluminum plate status is H 18, H 19, H38, etc.). Both are hard).
Semi-hard aluminum plate can be basically bent (H24 is also semi-hard).
O-state bending is certainly no problem, but because it is too soft, it is basically not bent in this state.
Secondly, should we choose pure aluminum or alloy aluminum?
The hardness of pure aluminum is not very good. It can be used together with 1 100, 1050, 1060, etc. 1 100 H24 is recommended.
Alloy aluminum has better hardness, and can be used in semi-hard states such as 3003, 3005 and 5052.
It is recommended to re-measure the sample. If the hardness of 606 1, 2024,7075 is too high, especially in T6 state, it should not be bent unless heated.
It is recommended to use 3003-H24, 3005H24 or 5052H34. The price is around 20 yuan, and the domestic price per kilogram does not exceed that of 40 yuan.
If the crack bends, the hardness should be too high.
Question 6: How to bend the semi-circle of aluminum-plastic board 5 points There are two common bending methods for the semi-circle of aluminum-plastic board.
One is the manual method, which has several preconditions.
First of all, make a semicircle with wooden boards, so as to ensure the same radian; Secondly, aluminum-plastic sheet is thin, good in toughness and elasticity, and can be realized by hand.
The second method is to use a three-roll arc starter, which is sometimes used for sheet metal forming.
Set it as the radius of curvature, and approach the agreed requirements after three rolls for many times.
The processing cost is generally around 15 yuan/m2.
Question 7: How to fold the curved aluminum-plastic plate Strictly speaking, the curved aluminum-plastic plate cannot be folded.
When it comes to aluminum-plastic sheet folding, the usual practice is to slot the back of aluminum-plastic sheet first.
Then fold the edge in the direction of the slot. One-step molding.
It is almost impossible to form 90 degrees or acute or obtuse angles without pre-grooving each other.
Aluminum-plastic plate can only be processed by rolling arc without slotting in advance.
Of course, nothing is difficult if you put your heart into it.
At the same time, the cutter head of the grooving machine is also fixed. When the grooving depth is ensured to be straight, flanging is carried out.
It should be possible.
Question 8: How to bend the aluminum-plastic board? Grooving with a V-shaped or U-shaped grooving knife can be bent without completely opening it.
Question 9: How to bend the aluminum-plastic board? Hello!
You can cut the aluminum-plastic plate according to the specific size, and then trim a line about 1.5 mm deep on the back of the aluminum-plastic plate according to the size to be bent, and then you can bend it. Be careful not to fold it too much to avoid the aluminum-plastic plate from breaking. The trimming depth of the trimming knife should not be too deep or too shallow. If it is too deep, the aluminum-plastic plate is easy to break and the angle is uneven. If it is too shallow, it will have no effect.
If bent into an arc, the aluminum-plastic plate will naturally bend as long as the aluminum layer on the back of the aluminum-plastic plate is torn with a vise.
Mu Feng's practice is easy to form edges and corners on the surface of aluminum-plastic plates. It is best to use detail workers or wood squares as the skeleton, and then lay a layer of 3~9 cm wooden boards as the bottom. If you paste it again, the fillet will be smooth.
You can contact online if you need it.
Question 10: How to bend aluminum-plastic plates with rounded corners? Mu Feng's practice is easy to form edges and corners on the surface of aluminum-plastic plates. It is best to use detail workers or wood squares as the skeleton, and then lay a layer of 3~9 cm plate as the bottom. If you paste it again, the fillet will be smooth.