Question 1: How to clean the metal strap? What if there is something dirty in the gap? Wearing the strap for a long time, the sludge accumulated at the joint of the watch or the surface of the belt mixed with sweat and dirt will greatly affect the beauty of the watch. When this happens, you can gently brush the strap and seam with a soft toothbrush dipped in some toothpaste or detergent, then rinse it with clear water, wipe it with flannel, and blow dry the strap with a hair dryer. In addition, K-gold watches will change color due to oxidation when worn for a long time. In addition to giving it to the master, you can also wipe it with tooth powder, and the effect will definitely satisfy you. In jewelry watches, consumers should not only pay attention to whether there are signs of loose diamonds, but also wash the dirty parts of diamonds with a toothbrush dipped in salad. It is also a good way to soak them with jewelry syrup.

Cleaning point:

1, in the process of cleaning, no matter how careful you are, there will still be water seepage. If the watch body is flooded by cleaning the strap, it will not be worth the loss. If you are worried about this situation, it is better to leave the watch to the master.

2. If the metal strap is wet (water, sweat stains, etc. ) and untreated, it is easy to rust. Metal rust or dirt can easily seep from the seams, stain clothes, and even cause skin allergies, so please remember to dry the seams with a cloth after taking off the watch or washing it with water. In addition, the diving watch can be washed with clean water after landing, but the use of chemicals is easy to cause injury.

3. Because of its soft material, the K gold strap is easy to be scratched when it is hit or touched improperly. In addition, the traffic exhaust in life, chlorine gas in the swimming pool or human sweat will make the K-gold watch discolor. Keep the watchband dry and put it on carefully, and watch made of titanium or high-tech ceramics with high hardness should also be careful to avoid hitting or falling. After all, hard doesn't mean invulnerability.

Question 2: Watch steel belt 1 How to clean and maintain it? First of all, it is necessary to check the pin and spring bolt between the strap section and the shell band regularly to prevent them from being detached or worn. If you run frequently, you should trim or replace it in time.

2. For watches with gold-plated case straps, it is recommended to wear them only in summer or change belts in winter.

3. Tungsten steel watchband should be protected from impact and excessive tension.

4, the strap discount part is the most prone to problems, which is also related to the usual wear. When opening and closing, the action should be gentle.

5, K gold or gold-plated strap, avoid contact with mercury-containing chemicals, prepare sweat-proof gloves at ordinary times, and do more surface scrubbing. Some platinum watchbands are rhodium-plated and cannot be polished, otherwise the background color will leak out and turn yellow.

6. The professional practice is to remove the strap for cleaning and use an ultrasonic cleaning machine. The cleaning method is to add detergent to clean water. According to the degree of dirt, you need to do more cleaning, then rinse it with clear water and blow dry it with an electric fan.

7. If you plan to clean it yourself, it is also recommended to take off the strap, add a proper amount of detergent in hot water, soak it for 10 minutes first, and then brush it with a soft toothbrush. Rinse with clean water and blow dry with an electric fan.

Question 3: How to clean the strap when it is dirty? Go to a professional watch repair shop to help you clean it, but you can't clean it yourself.

Question 4: How to clean the stainless steel bracelet at home? Cleaning method of stainless steel watchband 1:

Preparation: an old magazine, a clean plastic wrap, an old toothbrush and detergent.

Operation process:

Put the plastic wrap together with the magazine first, and then roll it into a tube, so as to prevent the book from getting wet when cleaning the strap later. Then put the watch on this rolled cylinder. Slowly enlarge the rolling cylinder of the magazine until the strap is completely opened, so that the watch will not fall off. First of all, it is convenient for later cleaning, and more importantly, after opening the strap, the stains at the gap of the strap can be cleaned.

The next step is to clean the strap. Clean the surface of the strap first, and then clean the stains in the gap of the strap. These gaps are closely connected, and it is difficult to clean up the dirty things inside. Now these gaps are all made of books, so it is natural to clean up the dirty things inside. Then clean the back of the strap, and also clean the stains on the surface first. Next, clean up the stains in the gap. Then the cleaning work is finished. Finally, clean the strap with clean water.

All the processes used have been completed, and all that remains is to put the strap in the shade to dry.

Cleaning method of stainless steel watchband 2:

Soak the watchband in boiling water containing detergent for about 15 minutes. Because the rings on this watch band are closely connected, the cylinder made of books can't open the gap at the connection. Put in hot water, it uses the principle of thermal expansion and cold contraction to make the gap at the joint open by itself, which is more conducive to cleaning. Next, you need to clean the strap. The method is similar to the first method and will not be described here.

After cleaning, soak the watchband in cold water for about 15 minutes. The purpose of this is, first, to clean the washing bubbles on the watch band; Second, using the same principle, the rising gap of the strap is restored to its original state. After soaking, dry the strap in the shade.

Question 5: How to clean the stainless steel strap 1? If your watch band is made of all stainless steel, you can soak it in washing powder water of about 60 degrees for 10~ 15 minutes, and then brush it with an old toothbrush to dry it or blow dry it with a hair dryer. 2. If it is not completely stainless steel, you can soak the strap in alcohol, acetone or gasoline, and then brush it to dry. 3. You can also use an ultrasonic cleaning machine (that is, the kind of equipment used by gold jewelry stores to clean jewelry). First soak in detergent 15 minutes or so, then clean, and you can clean.

Question 6: How to clean the steel strap of a watch when it is dirty? Wipe the strap with a cotton cloth dipped in toothpaste.

Question 7: How to clean the steel band watch? If you wear it for too long, which leads to dust accumulation or difficulty in cleaning, you can untie the watch (waterproof), put it in 30% alcohol solution or dodecahydrate and potassium aluminum sulfate (alum) suspension or 10% sodium bicarbonate (baking soda) solution, soak it for one hour (not too long), and then rinse it with tap water. If there are still floating ashes,

Question 8: How to clean the watch? Prepare for cleaning: an old magazine, a clean plastic wrap, an old toothbrush and detergent.

Operation flow: First, we stack the plastic wrap and the magazine together, and then roll it into a cylinder, so as to prevent the book from getting wet when cleaning the strap later. Then put the watch on this rolled cylinder. Slowly enlarge the rolling cylinder of the magazine until the strap is completely opened, so that the watch will not fall off. On the one hand, it is convenient for later cleaning, and more importantly, after opening the strap, the stains at the gap of the strap can be cleaned. Now let's clean the strap.

We should clean the surface of the strap first, and then clean the stains in the gap of the strap. These gaps are closely connected, and it is difficult to clean up the dirty things inside. Now these gaps are all made of books, so it is natural to clean up the dirty things inside. Let's clean the back of the strap again and clean the stains on the surface first. Next, clean up the stains in the gap. Ok, now the cleaning work has been completed. Finally, we need to clean the watchband with clean water.

All the procedures used have been completed, and all that remains is to put the strap in a cool place to dry. Be careful not to expose yourself to the sun, which will damage the quality of the strap.

Method 2:

We put the watchband in boiling water with detergent for about 15 minutes. Why are you doing this? Because the rings on this watch band are closely connected, the cylinder made of books can't open the gap at the connection. Put it in hot water, and use the principle of thermal expansion and cold contraction to make the gap at the joint open by itself, so that it can be cleaned. 15 minutes has passed, so start cleaning the strap! It's clean. Let's look at the water. It's dirty enough! This shows that the strap is clean!

Next, let's soak the strap in water for about 15 minutes. The purpose of this is: first, soak the detergent on the strap clean; Second, using the same principle, the rising gap of the strap is restored to its original state. Time's up. Take out the strap and dry it in the shade.

Question 9: How to clean the watch strap when it is dirty? There should be a special cleaning place where you buy it.