1. The general procedure of jadeite polishing is grinding, polishing and waxing. The polished jadeite blank must be polished in a large area first. First put a layer of polishing powder on the jade, and then grind off the burr on the jade surface with an oilstone. Because there are many tiny burrs on the surface of jade, the grinding process should be repeated 2-3 times.

2. Step 1: Paste. Apply a layer of paste polishing powder to the carved jade surface. Step 2: Polishing. Refers to grinding the surface with a 2000-mesh grinding wheel. Step 3: Paste and grind again. This step is repeated twice. Step 4: Use a brush. Coat the surface of jadeite with diamond powder, and then polish it with a hard brush.

3. polishing paste Generally speaking, there are two kinds of polishing paste of jadeite, one is green chromium oxide and the other is orange cerium oxide. In order to mark jadeite with different colors according to different degrees of color. Polishing jadeite, this step is to polish the surface according to the different polishing paste colors on the surface of jadeite.

Just dry the water on the jade. Although this step is simple, it cannot be ignored. Many people think this step is dispensable, but it's all wet. As we all know, wax is insoluble in water, so this step is essential. It is difficult to wax jade bracelets directly without drying.

5. How to polish jadeite with special polishing powder? Generally, red powder (iron oxide powder), green powder (chromium oxide powder) and natural diamond powder are used as polishing agents.

6. Paste, and paint polishing powder on the carved jade surface. Push grinding, grinding the jade surface with a 2000 mesh grinding wheel. Repeat the previous steps twice, and the color will fit better. Apply diamond powder on the surface of jadeite, and polish the surface of jadeite with a hard brush. If you don't notice the position, you should polish it carefully.

How to wax jadeite after polishing How to wax jadeite after polishing?

1. Heat the jade slightly, spray white wax powder on it, let the wax powder enter the gap of the jade, and then wipe it with felt cloth, so that the wax can be evenly wrapped on the jade surface. Soak jade in melted liquid paraffin. Although the methods are different, the principle is the same.

2. Step 1: Paste. Apply a layer of paste polishing powder to the carved jade surface. Step 2: Polishing. Refers to grinding the surface with a 2000-mesh grinding wheel. Step 3: Paste and grind again. This step is repeated twice. Step 4: Use a brush. Coat the surface of jadeite with diamond powder, and then polish it with a hard brush.

3. Jade should be cleaned before waxing, and then waxed with toothbrush. In the process of waxing, the wax liquid should be evenly brushed on the surface of jadeite, then the waxed jadeite should be evenly wiped with soft cotton cloth, and finally the jadeite can be dried in the shade.

4. Waxing. Waxing is to coat a thin layer of wax on the polished surface of jadeite to make it smoother and more shiny. Waxing itself is "essentially" harmless to jade. It just played a role similar to "beauty beauty". Therefore, waxing is also recognized as the process of optimizing ontology.

Which polishing powder is cost-effective?

1. The stone crystal powder, stone crystal flour and stone cleaning equipment distributed by Mei Sheng Trading Company in Nanhai District of Foshan City are complete in variety and reasonable in price. Mei Sheng Trading Co., Nanhai District, Foshan City has strong strength, pays attention to credit, abides by contracts and ensures product quality, and has won the trust of our customers with the characteristics of multi-variety operation and the principle of small profits but quick turnover.

2. Because it has the advantages of strong cutting ability, short polishing time, high polishing accuracy and clean operating environment, it is superior to other polishing powders (such as Fe2O3 red powder) and is called "the king of polishing powders". At present, this product is developing rapidly in China and its application is increasing day by day. Its output has soared and its development prospect is promising.

3. Alumina instead of cerium oxide is the best choice for polishing, but it is not ordinary alumina and must be specially made according to the precision of polished glass. For optical glass, the fineness of alumina is required to be finer. For the polishing of the crystal, the hardness of the crystal itself is higher, so the cutting speed and particle size of alumina are required to be higher.

4. Cerium-based rare earth polishing powder is one of the important rare earth products. Because it has the advantages of strong cutting ability, short polishing time, high polishing accuracy and clean operating environment, it is better than other polishing powders (such as Fe2O3 red powder) and is called "the king of polishing powders".

How to polish jade jewelry How to polish jade jewelry

The first step of the jadeite polishing process is to paste the carved jadeite, that is, to coat the jadeite surface with a layer of polishing powder special for jadeite, and then polish and polish the jadeite surface with a 2000-mesh grinding wheel, and then paste and polish it. Repeat the same step two or three times to give jadeite a preliminary polishing treatment.

Coat the carved jadeite with a layer of paste polishing powder. Use a 2000-mesh grinding wheel to polish the jade surface. Repeat the first two steps more than twice. After polishing, coat the surface with a layer of diamond powder, and then brush it with a hard brush.

The steps of jadeite polishing are as follows: passing through the oilstone: firstly, roughly polish the surface of jadeite with small oilstone. Moss: It is probably polished to make the jade surface look delicate and beautiful. Nailing: As shown in the figure, the tool is stained with diamond powder carving details.

How can I brighten the face of jade?

Emerald can polish and shine. First, use 2000 mesh sandpaper to polish. Adding water during polishing can take away the polished particles. On the polishing paste, jadeite is coated with a layer of polishing paste, the green one is chromium oxide, and the orange one is cerium oxide. Polishing is done with a cloth wheel. The time is about 10 minute.

First, the polished jadeite should be coated with a layer of paste polishing powder, and then the surface should be polished with a 2000-mesh grinding wheel. After that, paste polishing powder was applied and the surface was ground twice with a 2000-mesh grinding wheel. Coat the surface of jadeite with diamond powder, and then polish it with a hard brush.

Regular cleaning; First of all, friends who wear jadeite should wash jadeite regularly. The method is simple: soak jadeite in clear water for 30 minutes. If its surface becomes dirty due to long-term wear and tear, gently scrub it with a small soft brush after soaking.

Jade polishing generally requires six steps: polishing powder, rough grinding, fine grinding, polishing, cleaning and waxing.

How can an emerald shine? Ask the teacher for advice.

1. The seed material of jadeite is tender and dull, so it can be waxed. Because waxing after jadeite polishing can polish and smooth the jadeite surface, to a certain extent, make the jadeite surface more uniform and smooth, and improve the gloss and transparency.

2. Don't push too hard in the grinding stage. Plant tender stones. If you push too hard, those soft ones are prone to pits.

3. Maintain the tender jade bracelet, which can be cleaned regularly and worn frequently to avoid bumping. First of all, regular cleaning of jade bracelets helps to lock the moisture of jade, and jade bracelets can also maintain good luster and moisture.

4. From a realistic point of view, it is best to choose jade bracelets with high transparency, good cleanliness and old water. Don't need to raise. Like a pool of water. Water retention: I believe most people know that it is very important for jadeite to soak in water regularly. The water used for soaking must be clear water.