Method 1: Carry out basic cleaning.
1, put a cup of hot water in the bowl. Choose a bowl of the right size for the jewelry you want to clean. Cleaning most parts only takes about a cup of hot water. Heat the water in a microwave oven for about 30 seconds or more.
For example, to clean the paste, please add more water.
2. Put one or two teaspoons of baking soda. Separate a teaspoon or two of baking soda with a spoon and put it in a bowl. Then, stir them with a spoon to dissolve bicarbonate.
If it is difficult for you to mix bicarbonate with water, please heat it in the microwave oven for about 30 seconds or more.
3. Put the jewelry in the mixture for 5 to 10 minutes. Put the jewels in a bowl with water and baking soda. Parts must be completely immersed. Set an alarm clock for 5 to 10 minutes for baking to take effect. You can clean multiple pieces of jewelry at the same time.
The mixture of water and bicarbonate can remove dirt and debris from the surface, so all kinds of jewelry can be cleaned.
4. Wash the parts with cold water to remove the residual baking soda. After the jewelry is soaked, it is almost clean. Take it out of the bowl, pour the liquid into the sink drain, and then wash the jewelry with cold water.
If you want to clean small rings or earrings, please put cold water into the bowl. Therefore, they will not fall into your hands. If necessary, you can also use high-value jewelry to do this.
5. Dry the jewelry with a clean towel. After cleaning the jewelry, please find a clean cloth or wipe off the excess water with a paper towel. Dry one tablet immediately to keep it in good condition.
Wear jewelry or put it in a jewelry box.
Method 2: Remove stubborn dirt.
1. Mix three parts of baking soda and one part of water. Take a small dish and add three portions of baking soda. Then add some water to make a paste. The amount of baking soda depends on how many pieces you want to clean.
For example, mix three tablespoons of baking soda with one tablespoon of water to clean several tablets.
This is a good way to remove the residue from very dirty or stained jewelry.
2. Stir the ingredients until a paste is formed. Mix water and baking soda on the back of the toothbrush. Stir until a uniform paste is formed. If it is difficult to move, please add a few more drops of water.
If you think it's easier, please mix the two with a spoon.
3. Brush the paste with a clean toothbrush and use bristles. Insert the brush into the paste to get enough and completely cover the part to be cleaned. Try to transfer the paste to all the bristles.
If you need more baking soda, just dip the brush into the paste again.
If your toothbrush is inconvenient, please use a cotton swab. Never use a dirty brush, otherwise it will damage jewelry and spread bacteria.
4. Wipe the jewelry gently with a brush. You can clean it in your hand or on a paper towel. Put the brush bristles on the jewelry and rub them a few times. Clean one gem at a time.
For best results, please use a soft brush. They can touch the corners and creases of pendants, bracelets and rings well.
5. Keep rubbing for one or two minutes and clean thoroughly. How long it takes depends on the size and dirt of the jewelry. Wipe until the stubborn dirt disappears.
To see the effect of jewelry, please clean some pastes.
6. Remove baking soda and dirt with cold water. After polishing the jewelry, you can soak it in a glass of water or put it under the tap. Rinse jewelry for 30 seconds or more to remove baking soda.
7. Put the jewelry on the towel to dry. Stretch a towel near the sink, rinse it and put it on it. Put the jewelry on the towel for five to ten minutes to make sure it is completely dry.
Method 3: Clean fake gold and silver jewelry.
1. Heat a glass of water in the microwave oven for one or two minutes. Pour about a glass of water into a safe bowl and then transfer it to the microwave oven. Then put it in for a minute or two to heat the water.
2. Put the aluminum foil into the bowl to see the small pieces. Cut a piece of aluminum foil into the size and shape of the bowl and use it as the lining in the bowl.
If you want to clean large jewelry, you don't need to put aluminum in it. Its function is not to lose earrings and small pendants.
3. Put one tablespoon of salt, baking soda and detergent in the bowl. To make a detergent mixture, please put a tablespoon of salt, baking soda and detergent in a bowl. Stir with a spoon.
This combination is very suitable for removing refractory waste.
4. Soak the jewelry for 5 to 10 minutes. As long as they are completely submerged, you can put a few small gems in the bowl. If you want to disinfect small parts, please put them on aluminum foil to avoid losing them.
If necessary, please use the timer to know when to take off the jewelry.
5. Throw away the mixture and wash the jewelry. Water will remove all the salt, baking soda or soap left in the debris, as well as the remaining debris.
When there are no bubbles or residues in the water, the jewelry will be clean.
6. Dry the jewelry with a cloth after soaking. Before wearing jewelry or storing it for later use, please dry it with a clean towel. It can be cloth or paper towels.
Necessary materials
Wipe with baking soda paste
Three portions of baking soda.
1 serving of water.
plate
Toothbrush.
Soak the jewels in water with baking soda.
1 cup of hot water.
1-2 teaspoons of baking soda.
Bowl.
Spoon.
Use soap, salt and baking soda.
Microwave oven.
Bowl.
1 glass of water.
1 tablespoon salt.
1 tablespoon baking soda.
1 tbsp detergent.
Aluminium paper