Step 1, Step 1: Soak the ring in warm water for about five minutes, and take it out after the rubber bubbles adhered to the ring soften.

2, try with hot bubbles, glue is generally afraid of blisters, keep the water temperature for more than three days, I think it should be almost the same. But don't scald with boiling water, so as not to hurt amber.

3. See if you want to keep the ring cover. If you don't keep it, you can reduce it directly, but be careful not to crack the torus. If you want to keep the ring seat, it depends on the height of your pocket. If it is not high, use your own hair dryer to blow the heat, blow the glue soft, and then use a toothpick to push it out.

4. Wet your hands thoroughly. Rub soap, hand cream or some greasy cosmetics back and forth on your hands several times to fully lubricate your wrists and hands. Trying to take the bracelet off your wrist.

5. It is recommended to find a professional to remove the jade ring face from the copper holder. Because there are several claws on the copper holder on the jade ring, you can remove the copper holder by prying the claws with sharp metal.

Which is better for jadeite identification?

1. The way to identify the authenticity of the jade certificate is to look at the jade appraisal institution. To identify jadeite, you must go to a qualified authority. While identifying the authenticity of jade, we should also identify the authenticity of jade certificates.

2. National Jewelry and Jade Quality Supervision and Inspection Center, also known as National Inspection (NGTC), is a national-level jewelry and jade quality inspection institution authorized by China's General Administration of Quality Supervision, Inspection and Quarantine according to law, and is the authoritative organization for jewelry and jade inspection in China.

3. National accredited testing institutions. Such as (E 95) Wuhan Gold and Silver Jewelry Testing Center (Z 10).

4. Jadeite can be identified by an institution with gem identification qualification. Identification of jadeite can go to the local jewelry and jade quality supervision and testing center, which is more authoritative. In addition, in some jade crystal wholesale distribution centers, such as Sihui, Donghai and other cities, there will also be gem testing institutions.

How to take off the ring?

Find a long string first. Then put the rope through the ring. Wrap it around your finger slowly. After winding about 10 cm on your finger. Pull the rope down. Move the ring slowly. I dropped the ring. Take it off.

Method 2: Lubrication method uses lubricant. Many skin care household products can be used as lubricating oil, so that you can get rid of the ring unscathed. Some alkaline detergents containing ammonia (such as Wenjie) usually have the best effect. If your skin is damaged or scratched, choose your lubricating oil wisely.

The common method is to put your index finger gently on the ring and your thumb under it. Start turning the ring back and forth gently and pull it out slowly at the same time. Lubrication method uses lubricant. Many skin care household products can be used as lubricating oil, so that you can get rid of the ring unscathed.

Method 1: Put the index finger gently on the ring and the thumb on the bottom. Start turning the ring back and forth gently and pull it out slowly at the same time. Do not pull the ring too hard, or pull the ring. Otherwise, it will make the hand more swollen and the ring more difficult to take out.

First of all, when we usually take the ring, we usually use two fingers to hold the finger on the upper part of the ring. Under normal circumstances, we can take it off gently. If you can't take it off, you must use the following methods.

The general method is to put the index finger on the back of the stuck finger and the thumb on the abdomen of the finger, and turn the ring back and forth until it is pulled out. Be careful not to push or pull hard, or your fingers will swell up and it will be difficult to take them off.

How to remove the jade ring from the copper holder

1, pry the grab with sharp metal. The copper holder on Yuhuan can be removed by prying claws with sharp metal. Although the volume of the jade ring surface is usually small, each jade ring surface is carefully selected, and only the best part of the original jade will be made into the jade ring surface.

There are several claws on the copper plate for holding jade. You can pry open the claws with sharp metal and take off the copper tray.

3. Because there are several clips on the copper bracket on Yuhuan, you can remove the copper bracket as long as you pry the claws open with sharp metal. There are many such jade rings in the jade market, and the inlaid material is copper, which jade merchants call copper holders or copper frames.

4. How to deal with the jade copper holder: pry open the claw with sharp metal to remove the copper holder on the jade ring. There are many jadeites in the market, inlaid with copper (brass and white copper) and then displayed. Jade merchants call it a copper bracket or a copper frame.

The jade ring is always lost. What should I do? Will the jade ring break when it falls to the ground? )

1, hello! Jade belongs to jadeite in the category of jade, and its hardness is greater than that of glass. From this angle alone, the torus will not be broken. However, too high a height is impactful. I suggest you protect jade ornaments properly. If the answer can help you, please adopt it.

2, the ring surface is not glued, but the jadeite is fixed with platinum or 925 silver. If the surface of the jade ring falls off, you can go to the jewelry store and put it back on. Don't post it yourself. Adhesives are harmful to gems.

3, only a small part is broken, and it is still complete in general: it can be redesigned+carved.

4. But jade is not equal to jade. Jadeite is a kind of stone polycrystalline aggregate that reaches the jade level under geological action. It is mainly composed of jadeite or jadeite, sodium (sodalite) and sodalite (omphacite), and may contain amphibole, feldspar, chromite and limonite.

There is a finished ring and I want to change the ring surface. How can I get rid of the stuck torus?

See if you want to keep the ring holder. If you don't keep it, you can reduce it directly, but be careful not to crack the torus. If you want to keep the ring seat, it depends on the height of your pocket. If it is not high, use your own air duct to blow the heat, blow the glue soft, and then use a toothpick to push it out.

It is recommended to find a professional to remove the jade ring face from the copper holder. Because there are several claws on the copper holder on the jade ring, you can remove the copper holder by prying the claws with sharp metal.

Soak in water once, then push it up from below, and repeat it several times. Be careful to burn your hands. Another method is to blow air at the bottom of the ring with a hair dryer, and then push the surface of the ring out with something else. I also make beeswax.

To remove the glue from jade, you can clean it with water or wipe it off directly with an eraser.