How to make kite noodles

http://218.108.246.200/forum-9/show_thread----8813441-.htm

Method 1:

Materials

(1) 2 pine or spruce sticks (0.6 cm thick, 1 cm wide, 90 cm long)

(2) Kite surface material (plastic, etc.)< /p>

(3) Rope

(4) Scissors

(5) Wooden ruler

(6) Sticky strips

< p>(7)Small saw

(Chalk

(9)Wood glue

Use a small saw to cut a notch at the end of each wooden stick (see Figure 5-1). Be careful not to point the saw toward yourself. Measure the center of one of the sticks, make a mark, and place the mark at a point on the other stick. The distance between one end is 20 cm (see Figure 5-2). Use wood glue to stick the two intersecting wooden sticks together, wrap them with a rope a few times and tie them up (see Figure 5-3). Straighten the rope. 4 sawed small openings are used to create the outer frame of the kite (see Figure 5-4). Tighten the rope, and then tie the two ends of the rope into a knot at the four ends of the wooden frame. Tie the rope around a few times and tie it tightly.

Place the kite frame on a plastic film to make a horizontal sample. The stick should be pressed against the plastic underneath. Draw the sample with chalk 2.5cm outside the perimeter of the kite frame line, allowing the extra edge to fold over and cover the rope, being careful. Cut out the sample. Then fold the extra plastic around the rope and glue it tightly with glue. Now tie a rope to the notch at one end of the horizontal wooden stick and bend the wooden stick about 10 seconds. cm bend, and then tie the other end of the rope to the other end of the horizontal wooden stick. Add a bridle, and with the help of an adult, make a small hole at the intersection of the two wooden sticks, using a strip about 150 cm long. Tie one end of the rope to the intersection of the wooden stick through the small hole, and tie the other end of the bridle to the notch of the wooden stick at the bottom of the kite. Tie the rope used for flying the kite to the bridle. , the position is about 90 cm from the notch at the bottom of the kite and about 60 cm from the small hole of the bridle you connected. Keep adjusting this knot up and down so that the kite does not need a tail. Moreover, you can also fly the kite when the wind is low. Please remember to fly the kite in a relatively wide area and avoid high-voltage lines.

Method 2:

1. Design of kite pattern

When designing a kite pattern, fold the paper in half and draw the right side of the design drawing

Use light perspective to draw the other side

2 , How to cut bamboo?

Saw the bamboo into the required size and split it into half pieces.

Peel off the inner knots of the bamboo. Do not remove the outer knots for aesthetic reasons to avoid breaking the bamboo.

When splitting bamboo, if the thickness of the bamboo slices is uneven, the splitting knife should apply pressure to the thicker slices.

3. Shaping

Use a planer or a knife to flatten. Except for baking, do not bend it at will to avoid damaging the bamboo fiber.

First let one side of the two bamboo strips be completely aligned. Hold the bamboo strips firmly with your left hand and lay them flat. Release your right hand and use a thin pencil to draw on the two bamboo strips at about 1/2 of the length of the bamboo strips. A horizontal line

Don't move the long bamboo, turn over the short one and compare it with the long bamboo. If there is a gap, align the mark of the long bamboo, and draw a second mark on the short bamboo.

Take the center point of the two points on the short bamboo. This point is the center line of the length of the short bamboo.

With the inner side of the bamboo strip facing down, place the small blade on the center line, weigh the weight to see if both sides are balanced.

You can also place the center point of a short piece of bamboo on the main axis to see if it will balance.

Press lightly with both hands to bend it and check whether the arc is even.

4. Fixation of the skeleton

First mark the bamboo strips and smoke them with an alcohol lamp. When smoking, the bamboo pieces should not be too close to the fire or for too long, as the bamboo strips will be heated. When doing so, you should apply a little force on both ends of the bamboo strip with both hands to bend it. When the bamboo strips are too dry, soak them in water for about 2 hours.

When baking the wings, the ends of the wings need to be about 5 cm higher than the design so that they can be stretched open when glued to the kite cloth.

Compare the angle of the design, apply white glue, and use cotton thread to tie it crosswise in a cross shape.

Tie the wings according to the design drawing. The tail ends of the two wings must be about 5 cm higher upwards.

5. Cutting

When cutting the wing surface, leave an extra 1 cm for the sticky bamboo part.

6. Paste

Paste white glue on the skeleton. The white glue should be applied to the outer bamboo joints, but never to the inner bamboo joints. After applying it, stick it on the cloth. If the mask is made of silk, pay attention to the warp and weft when cutting the material.

7. Decoration and beautification

You can use strange ink for coloring. If you want to lighten the color, you can add toluene to dilute it.

Water-based advertising paints, etc. can also be used...

8. Lifting the thread

When lifting the thread, it should be lifted on the front of the kite (the side without the bamboo strips). The picture on the left shows the lifting The optimal position of the line and the angle of lifting the line can be adjusted depending on the size, structure, weight of the kite and the strength of the wind. The most suitable length of the lifting line is 1/2 of the width of the kite body.

9. How to tie the lifting thread

Whether it is an upper lifting thread or a lower lifting thread, its end must be tied to the bamboo strip to prevent slow buckling and slippage.

10. Connection of the fly line and the lifting line

Single-ring slip knot connects the pay line through the anti-torsion joint, wrap the pay line around once, tie a slip knot on the circle, and pull Lock it tight.

In order to prevent the line from knotting, you can use an anti-twist head - for fishing