Car film problem?
Generally speaking, junior technicians can only film the side windows, and only middle and senior technicians can film the front windshield with large curvature.

■ Check whether the installation of window glass and the integrity of automobile glass are intact before pasting, so as to ensure the normal operation of subsequent pasting.

■ Before pasting the film, the necessary parts in the car must be covered to prevent liquid from infiltrating. Sprayed cleaning liquid and lubricating liquid will affect decorative parts such as vehicle-mounted electronic equipment and interior seats.

■ Clean the inner and outer surfaces of the window before pasting the film (focus on cleaning the inner decorative surface and glass sealant area). This is mainly to prevent dirt or other construction quality problems between the pasted thermal insulation film and the window glass, and to ensure the perfect combination of the film and the glass.

■ Film pre-cutting. Measure the dimensions of the front and rear windshields with a ruler, and cut the film according to the measured dimensions. (The professional film pasting organization is through the computer, and the computer cuts according to the model. )

■ Spray installation liquid. It can avoid the appearance of gray spots, reduce the corrosion of edges, obtain the viscosity needed for solidification, and achieve better construction effect.

■ Dry baking and wet baking. Dry-bake the insulating film first, so that the insulating film can be fully pre-shrunk. In order to further improve the consistency of thermal insulation film, it is necessary to wet bake the thermal insulation film.

■ Squeeze out the installation liquid: scrape off the installation liquid between the thermal insulation film and the window glass as much as possible in the process of cleaning the installation liquid with a wiper, which can reduce the drying time of the thermal insulation film and obtain better bonding effect, overall performance and visual effect.

■ Check after pasting. "Look at it three times and pay attention to one thing": look at the whole insulation film for dust and bubbles, see if the corners are stuck firmly, and sit in the car to see if there is anything that affects the line of sight (especially the front and side glass). After pasting the film, it is recommended not to lift the glass at will within 48 hours.

When pasting the film, the most important thing to pay attention to is the use of a hair dryer. If you blow this place hard for a long time, it will lead to uneven heating and glass cracking. Therefore, it is necessary to find a professional authorized store for film pasting, so as to ensure the quality of film pasting and avoid the danger of glass breakage.

Also, car stickers are best in rainy days. When it is posted on rainy days, there is little flying dust in the air, which is conducive to beauty. Generally speaking, junior technicians can only film the side windows, and only middle and senior technicians can film the front windshield with large curvature.

■ Check whether the installation of window glass and the integrity of automobile glass are intact before pasting, so as to ensure the normal operation of subsequent pasting.

■ Before pasting the film, the necessary parts in the car must be covered to prevent liquid from infiltrating. Sprayed cleaning liquid and lubricating liquid will affect decorative parts such as vehicle-mounted electronic equipment and interior seats.

■ Clean the inner and outer surfaces of the window before pasting the film (focus on cleaning the inner decorative surface and glass sealant area). This is mainly to prevent dirt or other construction quality problems between the pasted thermal insulation film and the window glass, and to ensure the perfect combination of the film and the glass.

■ Film pre-cutting. Measure the dimensions of the front and rear windshields with a ruler, and cut the film according to the measured dimensions. (The professional film pasting organization is through the computer, and the computer cuts according to the model. )

■ Spray installation liquid. It can avoid the appearance of gray spots, reduce the corrosion of edges, obtain the viscosity needed for solidification, and achieve better construction effect.

■ Dry baking and wet baking. Dry-bake the insulating film first, so that the insulating film can be fully pre-shrunk. In order to further improve the consistency of thermal insulation film, it is necessary to wet bake the thermal insulation film.

■ Squeeze out the installation liquid: scrape off the installation liquid between the thermal insulation film and the window glass as much as possible in the process of cleaning the installation liquid with a wiper, which can reduce the drying time of the thermal insulation film and obtain better bonding effect, overall performance and visual effect.

■ Check after pasting. "Look at it three times and pay attention to one thing": look at the whole insulation film for dust and bubbles, see if the corners are stuck firmly, and sit in the car to see if there is anything that affects the line of sight (especially the front and side glass). After pasting the film, it is recommended not to lift the glass at will within 48 hours.

When pasting the film, the most important thing to pay attention to is the use of a hair dryer. If you blow this place hard for a long time, it will lead to uneven heating and glass cracking. Therefore, it is necessary to find a professional authorized store for film pasting, so as to ensure the quality of film pasting and avoid the danger of glass breakage.

Also, car stickers are best in rainy days. When it is posted on rainy days, there is little flying dust in the air, which is conducive to beauty.