Current location - Plastic Surgery and Aesthetics Network - Plastic surgery and medical aesthetics - How to paste the car glass film?
How to paste the car glass film?
Taobao authentic Johnson & Johnson film reminder:

Automobile window film requires high quality and construction level of automobile film, and strict construction level can ensure the final effect of automobile film.

1. Observe the installation of window glass: Before construction, be sure to observe whether the installation of window glass is in good condition and the integrity of automobile glass, so as to ensure the normal work of subsequent film pasting.

2. Dress of construction personnel and preparation of tools: The dress of construction personnel can not only reflect the personnel management level of the construction unit, but also have an important impact on the construction quality. In the process of film pasting construction, the construction personnel must wear uniform tooling and fasten all buttons. This can avoid scratching the paint surface during construction and the clothes fibers flying to the construction surface.

Sharp tools make good work. Movies are no exception. Construction tools to be prepared include: wiper blade, pressure watering can, hot air gun (power and wind speed), cutting tool, absorbent towel, fluorescent lamp, adhesive tape masking film and glass cleaner.

3. Cover the necessary parts of the car to prevent liquid from infiltrating: In order to ensure that the sprayed cleaning liquid and lubricating liquid will not affect the on-board electronic equipment during the construction of automobile thermal insulation film, and to ensure the initial state of the interior decoration to the greatest extent, it is necessary to cover the seats and instrument panels in the car.

4. Cleaning the window glass to be constructed: cleaning the inner and outer surfaces of the window (focusing on cleaning the inner decorative surface and the glass sealant area). This is mainly to prevent dirt or other construction quality problems between the thermal insulation film and the window glass after pasting, and to ensure the perfect combination of the film and the glass.

5. Film pre-cutting: Measure the dimensions of the front and rear windshields, including the length and width, with a ruler. Select the type of thermal insulation film to be constructed from the tool rack and cut it according to the measured size of the windshield. Our Shaanxi Master window film is directly pasted by the computer, and the computer will cut out the corresponding window film according to your car model.

6. Dry baking and setting (pre-shrinking) of heat insulation film: In order to ensure that the shaped heat insulation film can more accurately fit the radian of the window glass and reduce various problems that may be found in the process of direct wet baking, it is recommended to dry bake the heat insulation film before wet baking, so that the heat insulation film can be fully pre-shrunk.

7. Clean the outside of the windshield with glass cleaner and car wash mud, and spray the installation liquid: the main purpose of spraying the installation liquid is to ensure that the thermal insulation film can be better lubricated and moved during the construction of wet baking film.

8. Wet baking molding (adhesion) of heat insulation film: After the previous dry baking molding operation, the shape of heat insulation film basically matches the curvature of windshield, but in order to further improve the adhesion of heat insulation film, it is necessary to wet bake the heat insulation film.

9. Cutting plastic film: In the process of cutting plastic thermal insulation film, a construction worker needs to aim the fluorescent lamp at the cutting edge of the thermal insulation film in the cab, because it will be more convenient for people outside the car to determine the cutting construction position.

10. Clean the inside of the windshield with cleaning liquid and spray enough installation liquid: the purpose of spraying cleaning liquid is to avoid dust spots and reduce corrosion at the edge; The purpose of spraying installation liquid is to obtain the viscosity needed for solidification and better construction effect.

1 1. Remove the transparent protective layer on the film and stick the film on the inside of the windshield.

12. Use a wiper to squeeze out the installation liquid.

In the process of cleaning the installation liquid with the wiper, the installation liquid between the thermal insulation film and the window glass should be scraped off as much as possible, which can reduce the drying time of the thermal insulation film and obtain better bonding effect, overall performance and visual effect. The process of effect inspection is reassuring: under normal circumstances, the process of master film pasting can be simply recorded as: spreading towels from the instrument, keeping clean-cleaning the glass-cutting the film-setting a heat insulation film on the outer glass of the window-cutting corners according to the shape of the glass-cleaning the inner glass-formal film pasting-boiling water, blowing corners with a hair dryer-final cleaning, etc. If you want to paste the film you bought, please pay attention to asking technicians for help, otherwise it will be a particularly troublesome and headache to remove the glue later.