1. Install the neck pillow case. There is nothing to say. First, put two neck pillows to increase your confidence. Hehe, don't put it on in a hurry after loading it.
2. Install the pillowcase. Adjust the backrest of the front driver's seat backwards, press the two adjustment buttons at the same time, pull out the headrest, put on the pillowcase, and stretch and bond it to the end. (Note that the pillowcase will feel small at first, so it must be pulled to the bonding place evenly and forcefully, and the cloth ends on both sides will be stuffed under the front and rear tear buttons, which will feel very compact and integrated after bonding. )
3. Install the backrest cover. Do not invert the left and right backrest covers. The airbag opening is correct on the outside. Put it on and pull it down until it listens. At this time, you should sit in the back row and reach out to the bottom of the seat. You can feel that the PU leather material at the lower part of the rear side of the original seat is wrapped at the bottom of the seat. Hold the buckle, push it forward, slowly and forcefully release the buckle (slowly, you can do it, both buckles will release), then go back to the front row and push the extra part into the gap between the back of the chair and the seat cushion. Push hard, plug it in, and it won't break. Go back to the back row and pull out all the cloth you just pushed. At this time, you will find that the tear button can be glued! Pay attention to the PU leather of the original seat with two buttons I just mentioned, turn it over and stuff it into the seat cover, and stick the tear button on it. It's done.
4. Install the cushion cover. This thing is also divided into left and right sides. The cloth on both sides is long and short, and the long side has two elastic bands. Just put the long one with elastic band outside. Cover the front of the seat cushion cover first (ignore the two elastic bands first), then pull out the two long tear buttons at the back from the gap between the backrest and the seat cushion, extend forward around the bottom of the seat, and then wrap them around the plastic buttons in front of the upper seat cushion cover and stick them together. Then stretch the two elastic bands on the outside to the bottom of the seat and cover the bow spring on the bottom of the seat. It's done.
5. Have a rest and enjoy the fruits of the driver's seat. ...
6. Install the passenger seat as described above. After installation, you can have a rest and enjoy the fruits of the passenger seat. ...
7. Install two head pillows in the back row. Pay attention to open the backrest lock when pulling out, and lower the backrest appropriately, otherwise it will hold against the roof and cannot be pulled out.
8. Install the left rear backrest cover. Put it on, flatten it, put the cloth of the front bottom into the gap between the back of the chair and the seat cushion, put the seat at a 45-degree angle, take the bra out, adjust it, put the seat down, and glue it. (Note that it is most convenient to pull out the cloth when the seat drops to 45 degrees. When pulling it out, be careful not to be cut by the edge of the luggage compartment cushion. I have a bloody lesson here).
9. Install the right rear backrest cover. The method is as above. (Note that the right seat cover contains the central armrest, so it is better to install the central armrest cover first and then the backrest cover).
10. Install the rear seat cushion cover. Attention, everyone! There is a question that must be said first, which is a bit verbose, but it is very important. This link is the most important link in the whole installation process, because it involves the buckle problem of the rear seat cushion. It is absolutely correct that the plastic buckle in the back row rumored on the Internet is easy to break during disassembly. Because my disassembly also damaged a buckle (but it is already very good, I estimate that both will be broken), but you don't have to worry, the broken bayonet will not affect the ride experience at all. Go to the 4S shop and let the master install it when you are free. Super simple, super cheap (a few dollars). The following is the introduction: the rear seat cushion is a whole piece of soft material, and the bottom is fixed with four buckles, of which the back two are metal and hooked on the metal hook at the seat position, which is convenient and firm to disassemble; The first two are actually metal, but the reinforced bayonet in the slot of the car seat is plastic, and this reinforced bayonet is easy to break. First, push the seat cushion back as far as possible, then put your hand in the position of the back button and push upward. Try several times to untie the two buckles at the back. At this time, you can see that the mysterious cushion can be loosened. Then move the seat cushion back and forth. During the action, put your hand in the front button position and keep pushing upward. Hold on, then hold on. When you feel that the belt buckle is a little loose, apply force decisively and the belt buckle will be safely detached. (I didn't master this skill first, and the Force is quite strong, so I accidentally cracked it. After dismantling, the mentality of the buckle is better adjusted. Don't worry, take your time, and the result will be safe separation. Mentality is very important, hehe). After the four buckles are separated, the installation of the cushion cover is very simple: put on the cover, hang the 12 elastic band on the hook and hook them together. The process of replacing the seat cushion is similar to the above steps: hook the hooks of the back two buckles, install the slots of the front two buckles, and get it! (Before installing the seat cushion, pay attention to adjusting the seat belt buckle. )
1 1. Install the rear headrest, check the seat cover, sit down and breathe, and enjoy …
It's online.