2. After the high impact machine is adjusted and normally punched, close the soundproof box (except for the packaging of 8065 products at the border inspection).
3. During continuous stamping, employees are not allowed to hold products by hand within the range of the punch1m..
4. Technicians need only one person to adjust the mold machine, instead of two people.
5. Technicians can only adjust the machine feed outside the machine, and the distance is not less than1m..
6, the mold must lock the screw, 4 hours later to stop to check whether the screw is loose.
7. When there is a problem in the production process, it is not necessary to unload the mold. When the mold is directly repaired on the machine tool, it is necessary to turn off the power supply of the injection molding machine and hang a maintenance sign on the power supply box to repair the mold.
8. All tools should be put back in the toolbox after use, not on the machine, so as to avoid the tools slipping and hurting people.
9. When the machine is not in production, cut off the power supply in time.
10, short workpiece, using special tools, not directly feeding or holding parts by hand.
1 1. The producer should stand still, keep his hands and head at a certain distance from the puncher, and always pay attention to the action of the puncher. Don't chat with others.
12. It is forbidden for operators and mold repairers to put their hands into the mold during production.
13. When installing the exhaust fan, it is forbidden for the operator to put his hand on the motor to clean up the garbage.
14, slippers are not allowed to be worn at work, so as to avoid the molds and iron blocks in the workshop hitting your feet. Monitor, fitter and mold repairer must wear safety shoes when going to work;
15, it is forbidden for male operators to have long hair, and for female operators, long hair should be coiled to prevent it from being involved in the flywheel.
16, white oil, alcohol, cleaning agents and other oils should pay attention to fire prevention.
17. Materials, wastes and molds should be packed with gloves to avoid scratching their hands.
18, when there is oil, it must be cleaned in time to avoid slipping and falling.
19, gloves are strictly prohibited when drilling and milling machines; When using the grinder, please wear a mask and eye mask to protect yourself.
20, pay attention to drag the mold to prevent it from falling to the ground (the flat car should be driven to the lowest level to pull the mold).
2 1, it is forbidden for non-electricians to connect electricity to repair the machine.
22, it is forbidden to air gun blowing at people, easy to hurt your eyes.
23. Operators should wear earplugs.
24, found that the machine is abnormal, turn off the power first and then find the technician on duty to deal with it in time, not to deal with it without authorization.
25. The new employee's first day at work, the team leader must explain the safety operation procedures to him, and learn the safety operation procedures once a day in the first week.
26. When adjusting the machine, be sure to adjust the machine to single action. It is forbidden to play with the discharging belt in linkage.
27. Flammable and explosive articles shall not be stored under the switch.
28. Operators are strictly forbidden to play behind the workshop, so as to avoid wrestling, knocking over products or hurting themselves.
29. Inspect the equipment according to the inspection contents on the equipment check card, and pay special attention to whether the guiding and braking devices of the punch are working normally, and whether the functions of the Dan Chong and the punch are clear.
30. When installing a die on a small punch (10T), first loosen the locking device of the guide rail, install the upper and lower dies, then adjust the stroke of the guide rail until it meets the requirements, and lock the device. In addition, when loading the die on the high punch, it is necessary to go to Dan Chong. After locking the upper die, lock the lower die after hydraulic locking, and check again before production.
3 1. When unloading or picking up blanks by hand, special tools (pliers and hooks) must be used. It is forbidden to send or pick up blanks by hand. A single switch will hurt your hand, but you need a double switch. The machine must not leak oil, or it will fall down. Don't expose the power supply, it's dangerous.
32. Wear gloves when punching iron sheets, and pay attention, or you will hurt your hands.
33, at work, first check whether there is any abnormality in the operation of the equipment, such as unclear signal, unclear drilling, poor operation or electrical failure, etc., and immediately stop the machine and find the technician on duty to deal with it.
34. It is forbidden to use the foot switch in the punching machine, and all the original equipment of the machine is removed.
35, cleaning, inspection equipment, must cut off the power supply after operation.
36. Cut off the power supply, clean and scrub the workbench, dismantle and maintain it in storage, and regularly check the lubricating system oil every week.