1 color difference: check whether the same color lace of the same material has color difference; Whether there is color difference between the same roll and between rolls, it is required to measure the code length and weigh the actual weight when inspecting lace, and compare it with the delivery note and each roll of lace. If the quantity is not attached, it should be submitted to the team leader in time to report to the purchasing department for follow-up and recovery of the owed materials.
2 pairs of lace ripples; Wave matching includes left and right side wave matching and same side wave matching. If the waves are not right, you need to cut the board and submit it to the quality control department for verification.
3 flower-shaped round case; Check whether the pattern of the car flower is different or irregular, whether the car flower line has color difference, whether the car flower has jumper phenomenon and whether the bottom line is cut clean.
Lace alignment: according to the size of green order and delivery note, measure whether the incoming materials are consistent.
5. The difference between the lace incoming tolerance and the ordering tolerance is 2MM (this tolerance value needs to be studied and decided by the Quality Control Department of the production department).
Contents and standards of collar inspection of two flat knitting machines
1 Measure the collar size of the flat knitting machine, and check whether the ordered size on the green list and delivery note is consistent with the incoming size. The allowable error between the incoming material size and the order size of flat knitting machine is1/4'; If there is any discrepancy, submit it to the purchase order and follow up with the documentary, and send one copy of all colors and codes to the documentary batch to determine the size.
2. Check the order of magnitude and quality of the incoming materials of the flat knitting machine; Count the number of incoming materials and check whether there are holes, wire drawing and needle jumping. Indicate the number of defects in incoming materials on the incoming materials collection inspection report. Whether the color spacing of the color line flattening machine meets the order.
Check whether there is color difference in the same incoming material of the flat machine collar.
Check whether the flat collar is deformed.
Inspection content and standard of rubber buckle of three iron buckles
1 Check whether the number of iron buttons and rubber buttons is consistent with the delivery note, and confirm the color and model for the documentary drawing board.
Check whether the iron buckle and rubber buckle are regular in shape, and whether there is deformation, damage, scratch and uneven thickness of the buckle edge.
3 special iron buckle according to customer requirements; Need to pass the needle detector; Check whether it can pass the needle tester.
Inspection content and standard of four-way buckle
1 color difference inspection: check whether the incoming materials in the same batch have color difference and whether the male and female buttons have color difference.
2. Check whether the button foot of the buckle is yikou, and whether there is paint peeling and rust.
Whether the size and specification of incoming materials are consistent with the order and delivery note.
If you want to pass the needle detector, you should also check whether you can pass the needle detector.
Inspection content and standard of steel ring
1 rim size: check the green order according to the delivery note, and find the size drawing provided by the purchasing department according to the size and model required by the order. Check the radian, measure whether the length and width of the steel ring meet the requirements of the order, and compare the sample with the real thing to determine whether the size of the incoming material meets the requirements.
Check whether the coating paint on both sides of the steel ring falls off, and whether the steel ring has rust spots, oil stains, sharp corners and distortions.
Inspection content and standard of hexagonal steel frame
1 main inspection dimension of rubber reinforcement: measure whether the incoming dimension of rubber reinforcement is consistent with the order according to the green order and delivery note.
2. Check whether the glue bone is easy to break, whether both sides are smooth, and you can't scratch your hand. If it is easy to break, it means that you don't accept materials.
Inspection content and standard of seven-foot towel
1 color difference: check whether there is color difference between towels with the same batch of materials and the same color, and whether there is color difference between towels in the same box. Towels with obvious color difference are regarded as defective products.
2. Whether there is bending or deformation. Draw a towel with a length of 1 yard, and check whether it is bent to one side or not.
For woven towels, it is important to check whether the woven fabric is uniform and wrinkled.
Check whether the towel is smooth and whether there is hand covering.
Check whether there are stains, spots, rust spots and unqualified products, especially white, caused by yarn quality.
X. Inspection contents and standards of films
Size 1: The tightness and thickness of the transparent towel should be measured during inspection, and the tensile elasticity should also be tested.
Smoothness: it needs to be wiped by hand when checking, and the feel should be soft. Are there any adhesions?
Contents and standards of eleven flowers inspection
1 size: check whether the pattern size of incoming materials is consistent with the green order.
2 flower shape: check whether the flower shape of incoming materials is different in size.
Color difference: check whether there is color difference between incoming materials, flush flowers and flowers in the same batch.
Is the bow flower loose? If so, what is the percentage of incoming materials?
Every time you need to draw incoming materials, the color should be approved by documentary and the flower shape should be confirmed.
Inspection Contents and Standards of Twelve Kinds of Corn
1 Check the metal surface of corns for traces of inclusions, oil stains and deformation. If the corns are electroplated, it is necessary to check whether they adhere to each other and deplate.
Check the green order to confirm that the incoming materials meet the requirements of the order (including size)
Inspection contents and standards of thirteen kinds of thread and silk
1 check whether the incoming materials are consistent with the color number of the order, and whether the weight of several kilograms can be drawn from the line is consistent. If the weight difference is too large, it should be submitted to the relevant departments to study and decide whether it is necessary to make up the line (pay special attention) or reduce the price.
2. Used to measure the incoming weight of silk.
Inspection content and standard of zipper
1 Check the ribbon of the zipper for color difference.
Check whether the rubber teeth or metal teeth of the zipper are pulled consistently.
Measure whether the drawing length is consistent with the delivery note and green order.
4 whether the zipper is painted off, whether the metal teeth are rusted, whether the tail buckle is fastened, and whether the invisible zipper bolt is consistent.
Inspection contents and standards of packaging materials
1 All contents, including materials, need to be submitted to the real board or copy for document verification. At the time of acceptance, the warehouse must check whether there are mixed orders, mixed funds and mixed codes.
When accepting packaging materials, you must check the green order. When the received information is not clear, you must ask the documentary for clear information.
Because the packaging materials are not input into the system, all the receiving details must be submitted to the documentary to track the incoming materials. If the quantity is inconsistent with the delivery note, it should be indicated on the incoming materials list. The delivery note with overdue amount should be submitted to the corresponding buyer in time for material tracking. For the materials supplied by customers, the documentary will track the lack of materials.
Whether the blade of the list is even when cutting, whether it feels like an attacker, whether the size is standard and symmetrical, whether the printing should be centered, whether there is color difference between the list and the list, and whether the handwriting is clear.
Are there any discolored stains on the list?
Whether it is printing or pattern transfer.